Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hallo all,
I have just noticed that nRF5 SDK 11.0.0 do not have support for S110 softdevice anymore.
I understand that from previous project that S130 is able to do similarly...
Hello,
I have made a custom board using nrf51822 QFAC that has an IMU on TWI interface. For programming I am using ST-LinkV2 and OpenOCD. The board is working just fine...
Having spent numerous hours/days on trying to get the SDK12 examples running on my nRF52DK board with MacOS SES3.12, I in result wrote a basic guideline that in the end makes...
Hi,
i search a FSK tranceiver with a ADC readout for a experiment.
I need the raw ADC ("audio") signal for a external signal processing.
Please help, most of the wireless...
I want to transfer application over the air(OTA) to NRF51822, with using nrf-toolbox in android mobile so please tell me step by step procedure. and how to setup nrfDK to...
hello every,do you have the same question?
i delete the bsp relevant document,then i find that when i disconnect it from APP,it delay to Generate disconnect events. i use...
I'm trying out 6lowpan examples in the IoT SDK, and while everything works,
if I want to disconnect by running:
echo "disconnect 00:50:49:71:3b:44 1" > /sys/kernel/debug...
I have compiled the following list of error that are given by BLE Stack from the ble_app_gls code.
I would like to know what action needs to be taken on reception of all...
Hi everybody!
I want to do a connection between two BLEnano, one is the mater and the second the slave.
I have programmed the two BLEnano using the Arduino IDE and libraries;...
Hello,
I was wondering what is the best option/way to merge two functionalities which are developed in different examples of the nRF52 sdk12.2.
For instance, I would...
hi,
my device is nrf52832
i run my spi sd card driver fine in debug mode, but when i download it ( F8 ), it can not work!
so my question is what is the difference...
Hi,
I need to monitor radio channels and find the best one (with lower background noise) to use.
Is there any way to measure radio signal level in a particular frequency...
My problem: The run of my 1. DFU - Implementation delivers an error code after executing the line "err_code = ble_dfu_init(&m_dfus, &dfus_init);". For my opinion this is caused...
