Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
-----------------------------EDIT--------------------------------------
I've changed topic name, because not buffer overwrite is the problem.
I need some mechanism for...
I am working on a project for college in which I need to build my own PCB. The code works fine on the Dev Kit but on the PCB, the bluetooth is not showing. I have tried looking...
Hello,
I am using nRF UART v2.0 android app and I have added my custom logic above it. I am using this phone as the central device and nrf52 with sdk 12 as the peripheral...
hi
i am using two dongles.one would be sending sensor data from gpio to other through ble.i need a example code for those two.could you please tell me which example i can...
Due to limited budget, I have to use STLINK/V2 to flash code into nRF51822. I have been through steps of how to setup OpenOCD/STLINK/V2/nRF51822 in Ubuntu. After mass erase...
Hi. I'm using nRF52832, SDK13, S132v4.0.2.
I'm making peripheral device using nRF52832.
And I can see it gets BLE_GATTS_EVT_WRITE event as below when central sends WRITE...
I'm having a difficult time getting my project to link to the nrf_serial module
._build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol nrf_serial_read (referred...
Hi
From my understanding of the softdevice API, the maximum packet length is set using sd_ble_opt_set(BLE_GAP_OPT_EXT_LEN, &opt) , but the actual change to the packet length...
Hello,
I would like to build a sensor array that communicate with one master in a star topology.
I have played with the Gazelle protocol example ( gzll_ack_payload examples...
Hi,
I am working on a project where I have 4 advertising beacons which will have to trigger some functions in the central side when it gets the advertising data.
Now I...
Hi Nordic,
During DFU tests i had weird issue. If i compileed bootloader using your makefile everything works fine, instead of compiling with Eclipse IDE.
With Eclipse i...
code_template.c
, modified from developer.nordicsemi.com/.../bds_plugin_1.2.2_nRF5_SDK_11.0.0.zip
code_template.c, changed line #45 to
<%= field.FormatType() %>_t ...
Hi ，I am now using nrf24lu1p and 51822 for communication, the use of Gazell for paired debugging, and now want to use the upper authorities to close the NRF24LU1P Gazell pairing...
I've just read it and I am a bit puzzled? Could you explain why? I was planning to use gzll with one master and two clients where I would need to have at least two encrypted...
