I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I set up a project on the base of "BLE_APP_UART" to which I added header files and configured the sdk_config.h
Now I get these warnings during compilaiton:
...
Hi!
So I went from the Battery Service example to create my own service which went well and everything. Now I don't need a battery service, which is why I was trying to...
Hello,
i am working on Low current consumption project.
i have one question. what will be the good option to use the SPI or TWI ?
who have less current consumption ?
...
Hi, I want to ask some questions about BQ24090.
According to the schematic in the datasheet of BQ24090 , I have several questions below:
When should the led indicator...
I added the peer manager in my SDK11.0.0 application. I also have OTA DFU but everytime I boot into the bootlader, the first connection fails and I have to reconnect again...
Hi,
I am getting the "Couldn't connect Nordic_HRM" toast using the experimental project.
I saw the question but the answer there (sample code for selfie stick) is a very...
If I enable the Data Packet Length Extension and I enable the Connection Event Length Extension, having a connection interval of ~400ms I know that I can reach up to 251 bytes...
Hello,
I am trying to implement a Heart Rate Monitor Interface (HRMI) board with my nRF52, using the TWI_sensor example from SDK 12.2. I am unable to read any heart rate...
I use the S130 stack and enable the service changed feature when enable the soft device. I found the handle can be got when call add API. But this is GATT handle. How can...
UPDATE:02/28/2017
I MAKE A BOARD ,WANT TO KNOW DOES THIS PIC MAKE SENSE?
I WANT USE STM32F072B REPLACE JLINK OB.
STM32 HAS USB I WILL WRITE CODE MAKE A virtual...
Hi,
I download nRF5_SDK_11.0.0_89a8197 and open the SPI example in the peripheral folder using Keil V5.20, but I found that the project cann't be build. Could you tell...
I know the Source code for the MCP is not provided ..
I also Know the the masteremulator dll is available ... and there are several samples code demos available.
but I am...
hello,
In nRF 52, after executing ble_advertising_start after BLE_GAP_EVT_DISCONNECTED, although BLE_GAP_EVT_CONNECTED is set on the device side although the central is disconnected...
We are developing embedded linux platform and nRF52832 will be bluetooth peripheral. Since there will be an option to update linux kernel/file system we would like to be able...
