hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
How do you do！
I now use the chip is nrf51822AC, RAM space size of 32K. The size of the RAM occupation of my current program is
8K, I would like to ask, why this time the...
Hello Everyone
I am really new to everything here, i just got nRF 52832 board,
Can anyone please tell me the step-by- step method on how to make a program in keil uVision...
Hello,
I'm stuck in DFU using HCI(serial)..
I'm using nrf51822 , softdevice s110 ver 6.0.0 . I used example code in
"nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\device_firmware_updates...
Hi All,
I have a nrf52 PCA10040 Kit with me . I loaded the BLE app UART Central example binary into my Kit . The LED 1 is blinking (Scanning Indication) But am not getting...
I went though steps point here Everything went well. We create bootloader settings hex file base on our application hex file I'm a little confusing now. Should I always create...
Hi dev team,
in my design I am using the nRF52832.
On the GPIOs (P0.14,P0.15) I've connected a Darlington Array ( ST ULN2001 ).
My circuit is living of a super cap...
I coded following
BLE_GAP_CONN_SEC_MODE_SET_NO_ACCESS(&cccd_md.read_perm);
BLE_GAP_CONN_SEC_MODE_SET_NO_ACCESS(&cccd_md.write_perm);
char_md.char_props.notify = 1;...
Hi,
What does it means number 0x1D in p_ble_evt->header.evt_id in ble_db_discovery_on_ble_evt ?
I didn't get any error code, but service discovery is not completed.
Is...
I've noticed that Wireshark seems to occasionally report malformed data.
The malformed data seems to happen about 10% of the time and comes from all my smart beacons.
...
I am a beginner in the study of Bluetooth, and I have difficulty in understanding the purpose of API functions Bluetooth stack. For a better understanding of the system API...
I'm using MCP 3.1 and tried flashing the dongle from it multiple times. I also tried reinstalling MCP, but to no avail. When I flash some Blinky example using mbed it works...
I want to read whole flash memory using for loop and see how long it takes. What i have noticed is that it does not print all the lines. On the other side i ask myself: Does...
Hi,
I am very new to nRF51822 controller. i got some problem with compilation.
i have downloaded SDK v10.0xx and tried to compile blink example from following path.
...
Using Segger Embedded Studio 310i in Linux and SDK12.2.0, I imported the Beacon example project (ble_peripheral/ble_app_beacon) from Keil. Right now I'm trying to make it...
