Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi,
this is not a question about the nRF but about Android programming. Hope some of you can help me anyways. I modified the android part of the nRF Blinky example github...
Hi Nordic Team,
I saw some issue with Nrf connect on IOS.
First the App crash when i open it.
Second with IOS i can see some issue with pairing and bonding...
Hello,
I intended to implement an application without OS. Due to safety concerns I would like to have two call stacks : one for softdevice using MSP and the other for my...
After programming the Ble_app_uart to the nrf52832, I am sending a 100 Bytes of data from my UART Port to Nordic chip and this data is transferred over BLE to my Phone. I...
According to Table 19 in the nRF24L01+ datasheet, writing to any of the 32 command registers is "Executable in power down or standby modes only". This caveat is also repeated...
Basically I want to get a 8 byte long MIC when using the AES CCM encryption. From the product specification it does seem like I can only get a 4 byte MIC, is that correct...
Hello,
I try to flash my dev card nrf52 with the program ble_app_uart
Or a program ble by cons I can flasher by other program (pin change in), I do not know from where the...
I created an characteristic that has MAX_Length = 20 Bytes characteristic.
And When I'm trying to write less than 20bytes on this Characteristic, It Always send with 20Bytes...
Is it OK to send multiple packet continuously over nus at below way without waiting for packet transmit complete?
i=UserUart.RxBuf[1]+2;
index = 0;
while(i>0)
{...
Hi,
I'm using nrf51822 Ek kit and running ble_app_uart example,when i want to send any character or integer it Received like a string only,but i want to send only single...
Hi,
this question is more about iOS than nRF, but there's probably here some experience around this subject.
First the context : We have a product based on nRF51, S110...
I compile a .bin file for DFU. The bin file is 62020 bytes. I create the zip file for DFU, it is 62909 bytes.
If I extract the zip file, I get the bin file (62020 bytes...
We are currently designing a prototype board for our product using the nRF52832. We need to calculate the transmission line with on a 4 layer PCB. The stack-up looks like...
I am trying to use your swift iOSDFULibrary cocoapod. What I am doing is the following. I have a library written in swift. That library is where I have your iOSDFULibrary...