i have PMIC(I2C based )Max20360 that is developed using twi sensor , to this when i am intergrating a SAADC part throws error error # 134 :expected a field name . 1)why am...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello,
I’m having an issue with my setup: I have a nRF9160 running the bt/peripheral sample through a nRF52840 (running the hci_lpuart sample). It seems to work fine with...
Hello,
I am using nrf52840 MCU.
I am developing a product which have 2 I2C and 2 SPI interfaces. All the interfaces are on different pins.
I developed this thing with...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
If iOS of BLE master sends 4 packets of the same write characteristics with MD bit in the same connection event, how does SoftDevice of BLE slave work?
The ble_event_handler...
Is there a summary of potential pitfalls, i.e. issues which are asked repeatedly by users in these forums regarding HW/Schematic/PCB design for NRF BLE chipsets. Making mistakes...
I just published my port of a new FreeRTOS operating system version for the nRF51x22 and the nRF51 SDK 8.x.x to github.com/.../freertos_nrf51 , the README is copied below...
I am trying to implement some write to flash, and started by integrating the relevant functions from the example code I found in this thread .
I added a dummy write function...
Hello,
I'm building an aplication with multiple nRF51822 beacon modules. I'm using dual mode S130 softdevice. Sometimes, when beacon recieves a lot of messages, and forwards...
I'm trying to erase the page 32 of a nRF24LU1+ via SPI (using a Bus Pirate).
What I did so far:
Display the first 16 bytes of content of page 32: 0x03 0x40 0x00 0x10...
I have a switch connected on the nRF51DK Board. The switch is connected on PIN25 and PIN 28. I try to read the state of the switch.
My setup:
-nRF51DK
-SDK8.1
...
Hi
I am making some low-power wireless sensors powered by coin cells, which will sleep for long intervals between readings/transmits. I am using the micro ESB libraries...
Whenever I try to burn program to external nRF24LE1 with ISP interfacing from nRFgo Starter kit using nRF Studio, I am notified that chip on board couldn't be detected. I...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hi, Nordic staff.
I'm studying about the gazell for our next product of using gazell protocol.
I'm just wondering if there is a sniffer like a BLE for gazell protocol...
I often see that I cannot 'watch' variables in the watch window, and they just show as - even when I am stepping through a function and actually working with them.
Is there...
Hello,
I want to store some values to flash. What is the best method to store data to flash?
I'm trying to get pstorage working but i have no luck, so i'm wondering...
