Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
I am using Bluefruit BLE sniffer based on nRF51822 chip. Now Wireshark seems to decode most of the messages but not those where the actual information is being transmitted...
I was trying to develop a project using nrf51822. Which needs to send data over ble and do some functions according to the data received. In which I have to add a lengthy...
When I try to copy hex files onto my board, the board un-mounts and remounts with a file called "fail.txt". The files says "OUT OF MEMORY".
I have tried hard resetting the...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Is it possible to configure the radio in such a way as to always capture the entire packet, this means everything after the preamble including the CRC? Of course this means...
I am using SDK9.0,
J-Link Lite-Cortex-M, HW: V8.00, DLL: V4.98C
But getting this error just in this project when debugging:
debug.txt
It was working with this project...
Looking at the ADC HAL, I see 8 choices for ADC input, plus a disabled case. Is it possible to choose as the input to the ADC a node that is proportional to the VCC battery...
We're building a low cost device with an nRF8001 as the only means of communication as physical access is closed after the device is built.
Is there any way to change the...
Hi Guys,
I would like to set up my nrf51822 to make a connection once a GPIO button is pressed and send some data. I've been using this sheet to try and calculate what...
Hello,
I've purchased 2xnRF905-EVBOARD
I made some test with a spectrum analyzer. The output of the module is nearly 10dBm as mentioned in the datasheet.
I connect the...
I'm using PCA10028,SDK9.0,S130.I want to set and get the ble address,but I found that couldn't get the ble address by using API sd_ble_gap_address_get,the chip will reset...
Hi, there! Does peripheral with ANCS only be connected by iOS? I ran the ANCS demo in sdk 9.0, and it works well with iOS. Once an Android phone connect to it, it was connected...
On developer site I saw "The RSSI value of the beacon measured at 1 meter distance, which can be used for estimating the distance from the beacon." I don't get it can any...
I am using HID service over GATT and have several reports defined. When I increase my report map data size by adding more reports, my map size is 280 bytes, whihc seems to...
I want to try the nRF Sniffer app but that requires that I reprogram my nRF51 dongle. I want to know that I can restore it before I do this. I can't save the current "as-shipped...
