Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
I have a question on - to me - seemingly weird behavior about copying data out of the event from the soft device.
Situation: I have a 32 bit integer characteristic which...
Hey all!
Newbie here. I developed and tested some code on an NRF51DK easily enough using mbed, and now I'm trying to put it onto a PTR5518 module from Xuntong (which I...
Could you rub my nose in Bluetooth SIG Core or just explain what does chip do when switching to very noisy channel? For example Wi-Fi working very close to our device.
Hello:
I have read the documentation but I cannot determine if INPTR and OUTPTR can be set to the same memory address? I will try it to see what happens but it would be...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
Everyone,
I found out on that ble_app_power_profiling application is developed for Lower power current consumption....as It keeps system in the system_off_mode until...
Hi,
I am trying to measure and minimize current consumption .....
Following previous question on this forum,I found way to measure current on NRF51 DK by cutting SB9....
Hello Everyone..
i am new to nrf52 and this community.
i am using nrf52 and android master control pannel.
in my code i define my custom uuid base to ..
//430Cxxxx...
Hi, I'm looking for an easy way to use the UART in blocking mode (or something similiar) with a receive buffer that is filled in background:
If possible using EasyDMA...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi everybody
I am making a custom board which using ANCS (nrf51 sdk 9.0.0, softdevice 110 ver8.0.0). I saw on the original code have button_led_init() function to initiate...
hello,
I've encountered a problem with our own nrf51822 circuit not advertising.
Our circuit is exactly the same as what is given as the reference circuitry on the datasheet...
It's the first time i'm using the spi to connect various slaves, so is there any example how to communicate a raspberry with 2 or more nRF24L01 on the same bus?
Thanks in...
Today I have recieved the new nRF52 Development kit PCA10040. I did a update for the nRFgo Studio to version 1.21.2.3.
The softdevice s132_nrf52_2.0.0 will be flashed without...
