For the GPS tracker we are developing with nrf9151, the SIM provider is askign for support for the SIM-TOOLKIT .
Do we have any documentation?
Regards
Vivek
Currently we are exploring the features of BLE mesh to integrate this in upcoming project. In this architecture, we plan to use 2 Provisioner in the mesh and one of the provisioner...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
Hello,
I've built "bootloader" project in sdk6 and sdk8, which named "sdk6_bootloader.hex" and "sdk8_bootloader". Then what I did are listed as below:
(1)
using ...
I am trying DFU with:
BOARD_PCA10040,
nRF52_SDK_0.9.2_dbc28c9
s132_nrf52_1.0.0-3.alpha
One interesting thing is the SDK_0.9.2_dbc28c9 can not work with
...
Hi,
We currently (no pun intended!) don't have any battery protection circuitry for reverse polarity designed into our prototypes. Our device is powered from a CR2450 coin...
Dear Nordic.
I read specific data using GPIO(timer sampling), BUT, occasionally, the data is broken because of Softdevice interrupt.
So I want to guarantee it while reading...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
Hello everyone.
I would like to ask if is possible to compile and run examples from latest IoT SDK 0.9.0 on pca10028 board. Every example has only Makefile for latest pca10041...
Dear Developer Zone,
I'm using an nrf51822 with SDK8 & SD S110 v8
We have an iOS app connecting to a custom service on the NRF device. What we would like to do control...
hi,
i have a project which need dfu by OTA,but nrf51822 flash is not enough.The project detail information in the following:
chip:nrf51822QFACA10
SDK6.0
SOFTDEVICE:7.3...
I'm using nrf_drv_twi to talk to an accelerometer from an nRF51822 on a custom board. I'm on SDK 10.0.0. I'm following the example from the SDK, peripheral/twi_sensor. And...
Hi,
I set advertising data as follows:
err_code = ble_advdata_set(&advdata, NULL);
But I can't achieve advertising without ScanResponse，could you give me some suggestions...
Hello,
I do connections between 2 nrf51 with a known and static services. Is that possible to bypass the discovery to access a characteristics (i know all characteristics...
Hi,
I am having problems using the the dfu_dual_bank_ble_s110_pca10028 example on a nrf51822_xxAA device.
I have changed the memory ares to:
IROM 1: 0x3C000, 0x3C00...
So long story short - I need to pair two devices: Arduino UNO with Seeed BLE Shield and Adafruit Feather 32u4 Bluefruit LE.
Now, Seeed shield is configured, and is able...
