We have developed an application which uses the nRF9160 together with the same GPS and Ethertronics/Kyocera/AVX antennas as that of the nRF9160-DK . For the LTE antenna, we...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
I have a system using the Gazell link layer in which 2 devices stream data to a single host. Each of the devices is assigned a different pipe, and all three (host, and both...
I have successfully set up UART/Serial Port Emulation over BLE example. I have modified it so that it works with two nRF51 DKs, one acting as a central and other acting as...
Hello,
I would like to know whether the below PA can be interfaced with nRF51822?
For our application we need to increase the power of the BT. so I have selected the below...
Hi,
From other forum posts it seems to be very important to follow the reference layouts when designing nrf52 PCBs, but I can only find the reference files in Altium format...
Hi,
I have a nrf51 dongle and I try to connect my Android smartphone to it. My smartphone is BLE compatible, so no problems here.
I flash the firmware using master control...
I am a newer for Nordic's BLE.
and has WaveTek nRF51822 BLE Shield (design for Nordic), and downloaded the S110 softdevice version 7.3.0 and the wavetek_connectivity _s110v1...
Hi
I have some problem about the HomeKit SDK,is there anyone could help me?
In the HomeKit SDK,such as lightbulb project,there is a function mfi_i2c_configure that...
Hi Nordic guys,
we are developing a peripheral device with a custom protocol to exchange data.
we are using nrf51822 with SDK 6.0 and SoftDevice 7.1.0 (s110 being peripheral...
I can not find information about layer stack-up and whether the via-in-pads were filled, please provide this information. We are thinking about a variant with thin outer layers...
Hi, I am trying to combine SPI, microESB and BLE. BLE and microESB will not be combined in realtime, but rather be two distinct modes, and not run at the same time, and therefore...
[test result] change to use Timer1 of timer example,it failed. if you use timer0, it is OK..
SDK IS 9.0:
nRF51_SDK_9.0.0_2e23562\examples\peripheral\timer
[test step...
Is there a way to access the lower level clock which a connected slave uses to stay in sync with the master. We want to use this to keep our PWM in sync. We are looking for...
Hello,
After looking into forum regarding usage of S130 stack for using the device as both central and peripheral, I understood that the peripheral and central can concurrently...
Hi All,
I have query regarding PWM usage in nRF51-DK. I have a requirement to control 3 LEDs (brightness and power) simulatneously. I intend to use PWM for the same. But...
