Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi,
I have a the nrf51822 chip on a custom board and the ble_hrs code loaded on it. Now I would like this custom board to behave as a beacon with the hrs code sending data...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
ble_app_uart_c2.rar
I want to connect two PCA10001's together, one with the ble_app_uart for s120 using sdk 8, and one with the experimental_ble_app_uart for s110 using...
There's no question, I'm just posting this here in the hopes that it helps someone else out.
After I upgraded my Keil packs to the newest SDK (v8.1.0), my OTA FWU bootloader...
I have a problem getting both mesh and persistent storage to work. I am using the code from github.com/.../nRF51-ble-bcast-mesh and followed the document integrating_w_SD_apps...
Hi,
I am using
HW: nRF6310 + PCA10005
SW: s120_nrf51822_1.0.0_softdevice.hex + ble_app_multilink_central (\Keil\ARM\Device\Nordic\nrf51822\Board\nrf6310\s120\experimental...
Hello,
I am a newbie in in using BLE and exploring the nrf8001 DK. I was able to flash PCA 10000 module with updated firmware and it was detected in the master control...
Hi,
I want to read data ,wich is sent from beacon ,using usb dongle,and after this ,I want to send data received from beacon to pc through serial port.
Exist any example...
Hey.
I am wondering if there is a way to disconnect a slave from a master based on the strength on the connection and not when they naturally loose connection.
To give...
How do I block Bluetooth signals ? (I want the signals to be transmitted 180 degrees, not 360 degrees)
I have read it could be done with aluminium foil, but I have not...
I am looking at using an nRF51 in a BLE product (industrial applications).
One of the things that I have to sort of prove is that it will be a better choice than something...
Hi, everyone. I would like to be notified about the brown-out on my device. I know about POF peripheral, but lowest possible threshold is NRF_POWER_THRESHOLD_V21 (which is...
First off, forgive me for being a newbie at ARM programming in general. In AVR this was straight forward.
I have a circuit connected like this to the ADC (P0.01 = AnalogInput2...
