Hi everyone,
We're reading BAT level by reading data from ADC pin and the setup diagram is shown below.
We tested our device at hospital, and we observed significant...
I want to have two Kconfig flags that are both booleans but the build will fail if both are set. My code below used to work in pre ncs3.0, I'm wondering if there's a better...
Context:
VS Code
NCS 2.9
nRF54l15 custom board
Mac OS Sequoia15.5
peripheral_lbs sample project
Goal:
The goal of this project is to create a bluetooth beacon...
Why project config is not finding relative path of these files but absolute path works fine:
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip-DAC-Cert.der" ...
Hi!
We use nRF Cloud Log backend in our project. And during my research I found that it actually doesn't filter (despite the filtering code is there) messages generated...
I am looking for a solution where I can set custom and configurable root Kconfig file via Cmake cache variable, which can be specified through the west build command.
Steps...
I'm working on an Android app that connects to a Nordic nRF52833 BLE peripheral (Zephyr 3.7.99 / NCS 2.9.0). I'm encountering a consistent issue where:
The app connects...
Hi everybody, i want to read NFC tags and send them via BLE to iOS app. How can i do that? Can i work with nRF51822 and Elechouse NFC R/W ? www.elechouse.com/.../index.ph...
I'm using SDK 9, I flashed the softdevice 8.00
I compiled the project located in \SDK_9.0.0\examples\dfu\bootloader\pca10028\dual_bank_ble_s110\arm5_no_packs
I flashed...
Hey,
I am trying to use app_timers and nrf_delay_ms together but the system gets stuck almost everytime. I have the following code:
void timer_handler(void *p_context...
We have noticed an issue when using the UART on our nRF51822 (SoftDevice = S130, nRF51_SDK_9.0.0_2e23562). Our Nordic app waits for commands on the UART and processes these...
Hello Everyone
I am trying to configure the two GPIO in High Drive mode 5mA but after compiling the program it does not seems like congifured to High drive Mode because...
Hello, I am designing a system to transmit a mono or stereo audio signal over RF, a few hundred feet, then receive it and reconstruct the audio and listen to it on a speaker...
I am developing a HID keyboard with SDK v6.1, SD v7.3, IC revision 2.
The keyboard is already able to advertise (non-whitelist) and bond with iPhone, and connect/reconnect...
Hello
I want to optimize SPI com as fast I can do:
First I am using the fast spi data rate by SPI_FREQUENCY_FREQUENCY_M8 variable and I want to reduce at first the timing...
As far as i understood it supports 4.2 BLE because using it i'm able to see packets between nRF52 central and peripheral boards (HRM example). Is it so?
Question:
I am confused about who can do (or rather who usually does) whitelisting - the master or the peripheral device?
My findings so far:
I can't find a certain...
Hi,
I have written a windows 8.1 application to connect to my custom nrf51 device. It is used for configuration and is set up without requiring a password (I do not need...
I want to be able to transmit the on-board temperature and battery voltage over a beacon application. The application only needs to transmit periodically similar to an iBeacon...
Dear,
I'm now face problem on button interrupt.
I use 3 buttons for my system.
button 2, 3 is used for boot diagnostics. assigned as below.
bsp_event_to_button_action_assign...
I'm trying to lighten the leds using ble, my problem is that when I measure the current consumption when the leds command sent, it reaches to 5mA which is not suitable for...
