Hi,
I am currently testing the dect_shell example on two nRF9151 DKs and achieved a range of ~500m. I want to transition this setup into a multi-hop mesh network topology...
Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
Hi,
In the BLE_UART example code posted here , I noticed a discrepancy with the SD 3.0 migration document, SDK12, and the example code.
In stock SDK 12.1.0, ble_stack_handler_types...
Hello everyone, i need some help and suggestions in understanding what is exactly happening. I have read a lot about bugs and workarounds in pstorage and now i actually don...
Hi, when reading radio transmitter peripheral example, I got stuck a bit on radio_configure(). I got stuck because I can only get some brief from the corresponding .h file...
i m using nrf51.... first i have call WFI(); and device goes to sleep mode...and when press any switch on gpio so, wack-up again...so, may i know that.. how many way for wack...
i m using gcc toochain setup in windows for pca10028 devlopment kit... and load BLE_UART code inside it... and now i m add onother rtc code inside it.. but it's not work....
main.c hello sir.. i m place rtc example code inside of ble_uart code .. and i m using gcc tool chain setup for pca10028 bord... code complile sucsessfully... code not work...
Hello all,
I want to use a single bank bootloader with the ISP1302 Module (nRF51822 Chip) and S110 (V8) Soft Device, SDK 10, for application update
Can I use the BLE...
when i use nrfjprog.exe download my application code,Change nrfjprog.exe --eraseall --program ble_module.hex --verify --reset to nrfjprog.exe --eraseall --program ble_module...
My apologies, but I just want someone to give me a quick brief on what are these things and how they work. AFAIK, the nrf51xxx series SoCs render limited, sporatic radio availability...
Hi,
I am Working on a BLE application in which I do not want to expose certain services until I am securely paired/bonded to a valid device. The problem is that during...
Hi,
I'm trying to use sd_ble_gattc_characteristics_discover to figure out which characteristics are in a service.
On the whole it seems pretty obvious (keep calling...
I'm using the nRF52 + SDK11.0.0 + s132 and the ble_hrs example. The function conn_params_init() is called to initialize the connection parameters that the peripheral will...
Is there a way to pause all peripherals when hitting a breakpoint? In particular, I would like to freeze the RTCs when I hit a breakpoint. My app wakes up once a second, and...
I`m trying to operate PWM and soft device at the same time.
I have to make 4 Mhz using PWM block so I checked the PWM driver. There is no problem when using peripheral/pwmdriver...
Hello there.
I´m using a Taiyo Yuden evaluation board with a nRF51422 to connect with 3 different sensors. In addition to that there are also 2 buttons connected to the...
