Hi,
I am currently testing the dect_shell example on two nRF9151 DKs and achieved a range of ~500m. I want to transition this setup into a multi-hop mesh network topology...
Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
Hello, I'm currently using the nrf51822 and I'm constantly trying to send the accelerometer data to the NRF UART v2.0 Android Application.
But I do not know what I would...
Hi:
I want to get frequence hopping with gzl, Now I finish config gzl and commuicate successful between host and device. But I don't know whether frequence hop successful...
In s110 sdk 8, peripheral can connect one master and advertise in a non-connectable state simultaneously by here
but I did not find out how to confing non-connectable advertise...
This call:
SEGGER_RTT_printf(0, "%sHello %s%s%s!\n", RTT_CTRL_RESET, RTT_CTRL_BG_BRIGHT_RED, RTT_CTRL_TEXT_BRIGHT_WHITE, "World");
Produces this output on the J-Link...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
Hello everyone:
i'm testing the iot SDK 8.0, but got some problem with that.
Using the CoAP observable server example with it.
env: pca10028 + ble dongle + raspberry...
Hi,
What is the maximum rating for the nRF51's input RF level? It is not specified in the Product Specification for 51, though it is for 52.
Thanks,
Steve
By the migration of my application from nRF51 to nRF52, I can't compile the Nordic driver: nrf_delay.c
The IAR-Compiler gives that output by the build:
Error[Og010]...
Hi ,
I am using 2450bm14e0003 this instead of LNA circuit provided by NRF24L01P-R7 .Is it better to use this balun Ic or i should use the circuit provided by nordiac only...
I want to make a Bluetooth connection with nrf51422.
I am using the Keil software.
But I do not understand what the program will do the bluetooth connection.
Can you help...
I am running the Blinky code provided in nRF52 SDK examples.I am not able fix this error pointing at nrf_delay_ms. This function is hard to explain. Moreover I don't know...
To test one functionality, I am sending 1Kbyte of data to smartphone using nRF51 Uart example code.
I have tried testing with different baudrates, 9600, 115200, 38400,...
Hello,
I have an existing microprocessor application that I want to test with the nrf51822. I am currently using a different BLE chip. I do not want the trouble of porting...
I'm having a strange problem. I'm running the nRF51-DK with a dual-bank bootloader, S110 soft device, and my app under gcc. I'm using Eclipse Luna as my develpoment/debug...
When i added timer in my bluetooth code my board will not advertise.using pca10028 and nrftool box uart app on iphone 5s.
here is my complete code. Using timer1
Final with...
