Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Sorry if this is obvious but I cannot find the units of nrf_esb_config_t::retransmit_delay
in the SDK documentation, it just says: "The delay between each retransmission...
Hej,
I'm working with the nRF24L01+ and the ATmega328p programmed in c. The goal is to have both TX and RX mode in the same device, mainly work as RX but in certain conditions...
Dear sirs, I've had a difficult time establishing communication between my nRF24L01+ board and the SPI bus on my Arduino Uno R3 microcontroller. Could you please provide me...
Hi all,
I am thinking of using a GPIO pin's "SENSE LOW" to wake up my device from SYSTEM OFF mode.
In order to avoid the device keeps waking up in case the pin stays low...
I am using an nrf51822 DK with a (so far) very simple code along:
main()
{
//... init I/O
run();
}
Inside run:
run()
{
uint32_t retval = NRF_SUCCESS;
...
Hey,
I recently got the nrf52 DK and tried to make use of the app_button library to have easy to use debouncing.
As far as I understood the library, the event should be...
Hi,
i have a problem withr the example "BLE ATT_MTU Throughput Example".
I flashed the soft devive with nRFgo Studios. Now I want to flash the example, but i got following...
I have want to make application where beacon sends data to NRF52 and NRF52 to PC.
But if for example, the connection between NRF52 and PC is through bluetooth instead to...
Hi,
I have bought a new nrf52840 PDK. I have gone through the PDK user guide and I came to know that we can use qspi pins as gpios by cutting the Solder bridge connections...
Hi All,
I am getting following error while compiling template example with DSP CMSIS library in IAR.
Fatal Error[Pe035]: #error directive: "Compiler generates FPU instructions...
Hello,
I have a question regarding AVDD(35/36) pin. I am using nRF51822 QFAA package. And the reference circuitry on the datasheet uses a 1.0nF capacitor between AVDD and...
Hi, my first post here.
I'm a undergraduate student and newcomer to this field. I've some programming background but few in electronics and embedded systems (so probably...
Hi all,
Is there any DFU example using dual bank to the SDK 12.2? The secure bootloader example is for single or dual bank? . Sorry for the question it is no clear to me...
