i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
Hi,
I am using nRF52832 with S132_V2.0.0 and SDK_11.0.0.
I am able to doing dfu of softdevice and bootloader individually but when i try dfu for combined (SD + BL) then...
I can't find nrf.exe in C:\Program Files (x86)\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf
I only find nrfutil.exe in that folder.
Shall I use nrfutil.exe...
Softdevices have several separate version number systems:
a) the human-readable release version - used for hex file naming.
e.g. s110_nrf51_8.0.0, s120_nrf51_2.0.0
b...
Hi! I use a smart beacon kit (rev 1.0.0) and I would like to know how long the cpu is blocked during the data transmission/reception. I set the connection interval to 10ms...
We are designing a nRF52 based circuitry based on "53.2 Schematic QFAA QFN48 with DC/DC regulator setup"
In the reference diagram, there is an Optional block for the LFXO...
Hey all,
I've created HIDs using USB before which require a vendor ID (VID) and product ID (PID). Are these necessary when creating a device that uses HID over BTLE? If...
Is it possible for nRF52832 to drive an SPI TFT 240x240 LCD and a TWI Capacitive Touch Panel with BLE and NFC? Is 64Mhz the highest speed?
What I mean is that is it possible...
I am creating a project which must use two spi at the same time , the one store data to flash and the other use to communicate with FT221 .In the datasheet ,I realize that...
Hi Devzone,
We are currently awaiting arrival of our custom board, based on the nrf52 chipset, and I've been tasked with determining any potential gotchas with programming...
Hello,
I am trying to implement a star network with more than one datapipes enabled, where (between other tasks) the PTXs devices have to synchronize their clocks (real...
Hey, I am compiling some code to both read ADC measurements and send the measure it over UART. I looked at the ADC+UART+SOFTDEVICE example on github and I think I am pretty...
Can you please provide me the iROM and iRAM settings for the S110 softdevice for the nRF51822? Specify the SD version you are using please.
I'm reading nRF51822_Development_Kit_User_Guide_v1...
hi
i get vlaue with this line of code
but i did not specify what char should get it value
how can i get value from specific char?
i have nrf51422 v2 sdk v6
hi,
Everyone,
I was just checking on nrf51422 Dev kit for LFCLK and HFCLK oscillator configuration.
with lfclk set to start external oscillator ,it does not start external...
