Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
Hi,
I'd like to output some audio data through i2s. It's quite easy to understand your examples provided on infocenter, however, I can't get my code to work.
Here is...
Hi all, I'm working on sdk11.0.0 and s130 softdevice. In my project I need to take data from sensor board through uart and send to mobile through ble for every 500ms. Sensor...
Hi guys
I want connect nrf51822 (Raytac MDBT40) by my phone(HTC battery one android 4.4.2).
I use softdevice 130(ver.2.0.0) and SDK 11 demo code under KEIL ARM 5.
...
when i run sudo nrfutil dfu serial -pkg my_package.zip -p/dev/ttyACM0 i get the following error:
pc_ble_driver_py.exceptions.NordicSemiException: Failed to send init packet...
Hi
I am working with mbed targetting for ReadbearLab Ble Nano. I am trying to encrypt payload before sendind it with:
include "nrf_ecb.h"
...
int main(void)
{
...
Hi, i'm using keil and i would like to run the fpu_fft example to perform a fft. The example works if I set 128 or 256 as number of input vector data as you can see in the...
I'm using SDK 6 + S110 v7.
Is it possible to use device manager to perform bonding but don't write bond information persistently in flash?
With old bond manager I could...
Could someone please guide me through the process?
I believe it can be done through nRF Studio which I have downloaded, but don't know how to proceed from there???
Tks...
Dears,
I am developing a ANCS application with nus service on our product. There are a few problems I don't know how to fix it.
My problem is that :
1. ANCS will not disconnect...
Hey guys,
I have designed one custom PCB based on BMD301 in which I am observing some weird behavior on RESET pin. I have connected reset pin of BMD301 i.e. P0.21 to 3...
How do I deny a connection if the connection is unencrypted? I'm currently trying to do it with the peer_manager using
case PM_EVT_CONN_SEC_FAILED:
{
/** In some cases...
I have request similar to this questions but for SDK13:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
Judging by quick grep sdk_config.h from ble_app_template...
I am having some trouble getting the Power Profiler to start up correctly. Currently, I have the PPK DK plugged onto the PCA10040 DK. All of the onboard switches are set to...
