This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
Kindly help with some insights/tip on how to debug this hardfault. The code gives hardfault on my custom board, but not on NRF52-DK. My custom device is only populated...
Hi,
I am currently in the process of interfacing the HMC5883L magnetometer with my nrf52 development board. I have verified the connection to be working using a logic analyzer...
I have one central(SDK 10.0 S130) and one peripheral(SDK 8.0 S110) device. Normally central device can connect peripheral device it's ok but the peripheral device will stay...
Hi Nordic,
I'm porting hrs application on nuttx OS. But when I call sd_softdevice_enable function, it goes to "RESET". I read below article which mentions that SVC handler...
Hello all.
I'm having some problems with compiling the bootloader_secure project:
I downloaded SDK zip from http://www.nordicsemi.com/eng/Products/Nordic-Thingy-52 and...
Hi, I would like to detect the presence of a particular device in an environment where there are many devices advertising. The advertising packets are received by a scanner...
I want to send the continuous data over the BLE which is received by the UART of my nRF52 Evaluation kit. The BLE connection is getting disconnected while sending bulk of...
Hello Everyone,
I am new to BLE world.
Currently using MDBT40 which has nrf51822 as core: www.raytac.com/.../MDBT40-ANT-D.pdf
I am following this repo: github.com/...
I want to use nRF51822 Bluefruit LE Friend device (blue board) as BLE Sniffer. My OS is Windows 7 64-bits.
I installed ble-sniffer_win_1.0.1, v1.0: FTDI Driver Requirements...
According to another question here:
devzone.nordicsemi.com/.../
I'm stuck with waiting for the LFCLK to boot forever.
Normally, keil has a .s startup file that dictates...
Hi,I use the SDK 12.2.0, I want to add the peripheral RTC example to the ble_app_uart.I find the softdevice have used the RTC1 ,so I want to use the RTC0,but when I added...
Hello,
I am seeing something strange wrt to reassigning the NFC pins (9,10) on my Rigado BMD-300-EVAL using nRF SDK12.1 and gcc to build. I have two SPI based sensors on...
test_ble_mouse_wo_bootloader.pcapng Nordic_Mouse.pcapng connect_to_phone.pcapng test_ble_mouse_1.pcapng test_ble_mouse.pcapng Hoping someone here can help. The setup is a...
My problem seems to be related to this unsolved question.
I've making a central application to connect to my peripheral but I'm having a hard time getting the service discovery...
Hi friends..!
I am trying to print data on UART but only just after when TIMEOUT (180 sec) occurs in the project BLE.zip .
Is there something BLE stack event has to be used...
