I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hi,
I'm facing some problems in the use of the Logger module when the option NRF_LOG_FILTERS_ENABLED is set in the sdk_config.h file.
I'm working with the nRF5 SDK for...
I'm trying to get LPCOMP working on Zephyr - from my research online I can see no information about this currently so I'd like to find out how to do this.
According to an...
Hi,
The documentation for the nRF52840 (section 6.20.15.9) states that RSSI has a typical accuracy of ±2 dBm. I have measured signal strength at multiple distances, and...
HI,ALL！
I use official routine development NRF51822，nRF51\nRF5_SDK_12.3.0_d7731ad\nRF5_SDK_12.3.0_d7731ad\examples\ble_central\experimental\ble_app_blinky_c\pca10028\s130...
Hi,
My problem is with generating interrupts in lsm6dso relative tilt mode.
I asked it in st community, but I didn´t get any answers.
I'm trying to implement a relative...
Hello,
I couldn't understand the predefined header files for the spi, so I'm building the spi code from scratch.
To build init_spi function, It's clearly mentioned in...
Hi,
We are currently trying to design a system using one of the nrf5 bluetooth chips. However, we are still in the process of designing a functional antenna and need to...
Hi, I am trying to implement an example that support multiple peripherals (HRS & UART). When I get a connection (from either) I get the BLE_GAP_EVT_CONNECTED. How can I differentiate...
What is exact difference between heartbeat and health models?
I know heartbeat can be used to detect node outage, but so can be health message?
So, which one should be...
When starting up the device with the nRF5 SDK 3.2.0 for mesh, even though the model and subscription list state is loaded from flash, it is stored again right afterwards....
To the kind attention of Nordic support team,
I was reading this blog https://www.ericsson.com/en/blog/2017/12/wake-up-radio--a-key-component-of-iot
May I ask if Nordic...
After Downgrade protection in the NRF9160 has been set with AT%XPRODDONE=1, switching it off with AT %XPRODDONE=0 returns ERROR. Is there a way to disable downgrade protection...
Hello DevZone,
Is there a way for hardware to update the timer capture register?
I want to create different frequencies using a single timer. Next to the timer, Bluetooth...
I am using Nordic proprietary RF receiver and transmitter. I want to display the received data on my serial terminal using UART pins (any 2 pins as Rx-Tx) .
When I tried...
