Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
My company is using nrf52832 and our certification agent (we will apply for CE Red and FCC for our device) is wondering if the chip manufacturer is a SIG member, otherwise...
Hello I am new on KEİL and NRF52832,
I am trying to merge this custom service and Ble_app_gls example . I added custom services libraries to ble_app_gls example ,I added...
Hi,
I want to set a custom value to my Gatt characteristic value. I can do this by writing to the characteristic in my app or the NRF_connect application.
What I want...
Hi,
I am using sdk15.3 for a project, the uart works fine when programmed without bootloader, but just after add bootloader, the uart is not worked now, also the rtt log...
Hi all, This just works in other compilers. I'm new to Nordic/Segger and have tried all variations of parenthesise, ## macro expansion. It's got to be something simple! #define...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Dear Sirs,
We are creating a solution based on your chip, but have heard that it is / might be discontinued.
If that is the case, what would be the replacement model...
Nordic SDK 15.3.0 ble_app_gls merge with custom service
Hello I am new on KEİL and NRF52832,
I am trying to merge this custom service and Ble_app_gls example . I added...
Hello
Would someone ,please reply to the below thread,waiting for the response
https://devzone.nordicsemi.com/f/nordic-q-a/60891/unable-to-read-the-128-bit-uuid-with-base...
Hello how are you?
I'm using the mesh example Light switch example from nRF5 SDK for Mesh v4.0.0. I implemented the RSSI util model and it is working, one question I have...
I am working on a new design and i am using ST7789 (240 X 320 pixels) screen with nRF52840, it is working fine. I have followed the code provided in SDK example (big thanks...
Hi,
I´m trying to add a new, custom TX characteristic to Softdevice. I use example from SDK 16 "UART/Serial Port Emulation over BLE".
How I can do this, is explained...
Hi,
I flashed and run "ble_app_uart" example on nrf52833 DK. With an UART tool, I can recieve data from smartphone (rx characteristic) but I can´t send data from UART tool...
