Hi,
We are running into a serious issue with OTA. Specifically, we have observed that nRF52832 will not be able to perform OTA to a newer firmware given that it is previously...
Hi all,
I'm trying to characterize the UDP throughput of a Thread network consisting of nRF5340 DK devices. I saw that Espressif made a test report and they seemed to use...
I’m using a custom PCB based on the Minew ME54BS01 module (nRF54L15 SoC) for both ends of our proof‑of‑concept: one node as a GATT‑based Channel‑Sounding reflector (leveraging...
Dear DevZone support,
I'm currently evaluating nPM1300 for Lithium Polymer battery management and charging and would like to ask a question.
I understand that I can...
Hi Nordic:
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
Hello Everyone,
I have deveoped my custom Board using(NRF51) which has four test pins VCC GND SWCLK,SWDIO. I would like to program the custom board. So could anyone tell...
I'm getting the following log messages when I try to initialize the BLE stack:
First from CHECK_RAM_START_ADDR, I get:
RAM START ADDR 0x20002080 should be adjusted to...
Hi,
I want to debug the blinky project on a nRF52 dk (PCA10040) using Eclipse. I strictly followed the instructions as described here: devzone.nordicsemi.com/.../
I...
Hi,
Is there any documentation regarding nRF OpenMesh( nRF51-ble-broadcast-mesh) Security ? Explaining the security of the communication between nodes in the Mesh network...
Hi all,
I'm working on mbed os and I cannot use the softdevice_ble_evt_handler_set and SOFTDEVICE_HANDLER_INIT . Every time I build it, I get:
undefined reference to ...
Hi ,
I am using S120 ble_app_multilink_central example. I have configured UART0 in interrupt mode. I send some command and expect some response. It work very well in starting...
Our product is based on nrf51422_CEAA chip with softdevice S110, SDK 8.0.0, dual bank ble bootloader DFU.
We have modified the dfu bootloader example from SDK 8.0.0 to...
I read a document, "Setting up production test using DTM", "nAN-034 Application Note v1.0".
And, Figure 3 shows how to setup test environment.
But, I cannot find which S...
DCDC_testing.zip
Hi,
I am in the process of reducing power consumption in micro esb mode. I use the following code, just for testing. The following code consumes 18mA unlike...
It is possible to load a new firmware in a NRF51822 PCBA using the Nordic Development Kit NRF51DK?
Do I need a special connector?
This is the beacon Module I pretend...
Hello,
I have a board with an RFDuino on it which uses a Nordic nRF51822 internally. We are seeing a few of them auto-brick when the input voltage dips too low.
My first...
I have a question about the usage of Flash Data Storage, chunks and parsing of the data retrieved from FDS.
How, when and why are you supposed to use "chunks" when setting...
Hello,
I would like to implement an interface with an external SPI ADC using the nRF52832.
The ADC has a RDY (ready) signal that goes low every time a new sample is ready...
Hello,
I have simple custom PCB with nRF51822.
I am trying to make it advertise like a beacon, by program it with ble_app_beacon example from nRF5_SDK examples.
I have...