Hello, I hope you are well.
I created a new driver for an i2c accelerometer with 2 gpio interrupts, but it does not build properly. When calling `static const struct device...
Hello everyone,
I'm working in a ble project that use uart interface. When I sent string data in nrf connect app, the uart_event_handle is not called.
I started my project...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
nrf5340DK
NCS 3.0.0
if I use sample zephyr/samples/boards/nordic/system_off it works fine and i can wake from sw0 press. but if i move the sys_poweroff() call int a...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
i have some bare-metal RF code that runs on my nRF52-DK, which i'm currently porting to my nRF54-DK.... functionally, everthing is working just fine -- the boards can in fact...
Hi
I am trying to port some PWM code from the NRF54L15 it uses HAL access because i have found it has faster writes which are useful for my application (testing latency...
I implemented the function of DFU using NRF SDK 17，Implemented dfu using MCUboot with ncs 2.9.0
Can the dfu of MCUboot in ncs 2.9.0 upgrade the program of nrf sdk 17
I'm hitting a wall with implementing nRF7002 + nRF52840 without Zephyr.
I've worked with nRF52's for about 8 years now and on about 30+ products, all using the original...
Hi, I'm using the nRF52840 DK with SDK 17.0.2.
I've set selective_auto_ack to true , which should allow the use of dynamic ACK (or ACK payload).
I have two types of data...
Trying to get set up with my new PPK2. Installed NRF Connect and JLink on my Win11 system. When I select the device in the Power Profiler software I get an error. Searching...
Hello,
I am trying to download nRF Connect for VS Code extension but the extension is not found. There is just no result when searching for 'nrf connect' or something...
I am using nRF connect SDK v2.9.0 with a custom developed board that looks like this:
I tried the ' Bluetooth LE LED Button service' sample as it's and noticed that...
I have a board with the npm1300 and a nrf58240. I'm trying to read some status registers out of the npm1300 to debug some trouble we are having with it. It doesn't seem to...
I upgraded the SDK to 3.0.0. and now I have an issue:
"Actions/Flash" command fails with "Timed out waiting for RRAMC.READY.". "Actions/Erase and Flash" works.
I am on...
We have a project that includes a custom board definition and out of tree driver with folder structure as follows:
Our project builds successfully with SDK v2.7.0...
Hello, please help. I want to use nrf54L15 to connect to Bluetooth devices (Bluetooth headsets or other Bluetooth devices) and test the throughput between them. Is there any...
Hi Team,
I am setting up an OpenThread Radio Co-Processor (RCP) using the nRF5340dk. However, I could only find examples for the nRF52840 and other chipsets but not for...
Hello,
We are currently in the R&D stage for our Smart Home automation project, and we are evaluating the use of the nRF54L15 SOC with Matter support for our products. Our...
Hi
I am working with a custom board with nrf52832 with only 32Mhz external crystal. My application is working in the nrf52832 development kit but when I use the custom board...
