Hello,
I am trying to measure nRF9151 current using Power Profiler Kit II, running Cellular UDP project on EVK and following the steps in:
https://docs.nordicsemi.com...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
We are developing a very low power product. In some cases like not getting registered, PSM not being available, ... we want to drop the connection and go to a sleep state...
Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
According the the instructions for the Thingy mesh demo, it is possible to manually provision new nodes. Is it possible to identify the unprovisioned node first by sending...
I am trying to make the nrf52832 enter in ON/low power mode for inactivity periode.
I must have the "System ON, No RAM retention, Wake on RTC" as indicated in nrf52832 datasheet...
Hi,
I run the Secure DFU, and I'm doing OTA update without any issue.
The problem is the case that I'm doing an OTA update with a application-version smaller than...
Hi all, Nordic distributors no longer carry the nRF52840-PDK, which included the NFC antenna. What is a direct replacement for the Nordic NFC antenna that used to be included...
I am trying to connect a BerryMed MD1000 Pulse Oximeter (BLE Server) with an Adafruit Bluefruit Feather (nRF52-enabled) Arduino board (BLE Client).
I made an Arduino sketch...
hi All!
I use WAKE UP event from G-SENSOR on some GPIO to wake up the MCU on motion detected.
But sometimes ( ~1% ) the event does not occur for unknown reason until RESET...
Hi,
I want to have 2 SPI slaves on the same bus.
I saw in other posts that in the past it was not supported by the spi driver and that i should use NRF_DRV_SPI_PIN_NOT_USED...
What will be the real time effect if we give high value to Tx rather than keeping default Tx value as '0' ? Will it increase signal range?
Regards,
Ashiq Mohammed
I need nRF connect & toolbox on my iphone to do evaluation.
There is nRF toolbox, nRF Beacons but no nRF connet in App store.
Where can I find nRF connect ?
thanks ...
Hi.
Why longer advertising data destroy device ?
When I set length of advertising data to 20bytes in advertising_init(), device will crash and I can't download new firmware...
Hello,
The sd_softdevice_enable returns 8 (captured with my jlink probe), how can I investigate please ?
Configuration:
SDK 15.0.0, SD_132_6.0.0 with bootloader
In my application, I use the peer manager that has called the fds_init function, should I call it again if I want to use the fds to store my data. Will the peer manager use...
Hello Everyone,
I am using Nordic's Power Profiler Kit to estimate the current consumption of an external board. I have been able to configure it properly and getting results...
On nrf52840 I get a current of ~10 uA while sleeping. At the moment I don't run any code and don't start up the softdevice. I go directly to sleep with __WFE(). The result...
