Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
hello,
i am uing nrf51822.now i am in trouble while running uart on nrf51822.please tell me which can i have to burn on nrf51822 for getting uart properly working.i am using...
Hi,
Is there any information on how much improvement the DCDC has over the LDO at 1.8V? I'm working on a heavily space-constrained application, and I'm trying to make a decision...
Hi, i am working on PWM Library example in which i a m configuared GPIO pin P0.25. then i am getting voltage variations 1.3 to 2.8 volts.
the problem is when i disable...
Hi,
I want to connect old nokia 3310 to NRF52 DK.
Please let me know if any one has information about it?
Based on my research old nokia phone uses M bus and F bus...
Hi,
We're working with very specific hardware which requires us to watch very closely. We're currently considering a blocking function in an ble event handler which can...
Hi all,
We are currently developing a BLE enabled sensor device. We want to use the NFC component to identify the sensor by writing a device ID to the tag.
Question...
Hi,
The comparator (COMP) in nRF52 can use three internal reference voltages (1.2, 1.8 and 2.4V). Is it possible to also output these voltages on IOs?
Best regards
...
hello there in my code,
APP_ADV_INTERVAL 64
APP_ADV_TIMEOUT_IN_SECONDS 5
using nrfsniffer i am getting 57 packets in 1 second.
i can't understand it. because APP_ADV_INTERVAL...
Hi!
I tried to some research in the forum but I would like you to assert my final decision.
My goal is to design a sensors network (at the beginning with five end-nodes...
I am working with some code from a previous provider and I found in its void bsp_event_handler(bsp_event_t event) function this code:
case BSP_EVENT_MID_PRESS:
err_code...
Not sure if this is the proper venue for a bug report:
In nrf_nvmc.h (from SDK v12.2.0)
/**
* @brief Write consecutive words to flash.
*
* @param address Address...
Hi,
We need to add WeChat / AirSync functionality to our nRF52-based product. Is there any support available from Nordic for this kind of environment? For example ble_wechat_service...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
