Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi, I have problem with discover services in advertising mode on NRF51822-BEACON. There is default firmware in this beacon. I using Xamarin on Visual Studio 2015. It is connected...
I have integrated IAR code into my company system.
with the Jlink_monitor.c, jlink_monitor.h , jlink_monitor_ISR_ISR.s and enableMonitorMode.mac.
Step 1: I loaded code...
Hi,
I am trying to use the nrf_drv_twi class but I cannot define a nrf_drv_twi_t instance. When I write the code
`nrf_drv_twi_t twi = NRF_DRV_TWI_INSTANCE(0);
I get...
Hi,
It is indicated on page 59 of the datasheet (rev1.0), concerning the register nr.8 OBSERVE_TX, that "the counter PLOS_CNT is reset by writing to RF_CH . See page 75...
I am working with SDK12.2.0. I see that transports seem to be registered as section variables with the identifier dfu_trans
I have added a section definition in flash to...
Not sure if this is a typo in the function comments or a small bug, but thought you'd probably want to address it either way. I'm on the most recent NRF5-SDK (12.2.0) and...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Gentlemen,
I'm trying to develop a Health profile solution that works with Win 8.1
I'm using SDK 6.0 and S110 v 7
Win 8.1
I found the Win 8.1 sample app...
I am looking at the Master Emulator examples ProximityDemo and HealthThermoDemo. I can use both to connect to one device that I have (Device A). I try to use ProximityDemo...
Hi,
I want to achieve DFU OTA nRF51 using NRF52832.Is it any example,or data transfer message sequence charts documentation? Could you give me some suggestions?
Thanks...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi,
I hope you are doing well. I am working on nrf51822 project. I want the nrf51822 to advertise for 5 secs and then sleep for say 30 mins or an hour and then wake up...
hello,
Starting nRF 52832 (s 132), leaving idle, after 3 minutes, ble_event_id 0x1b will occur, then BLE communication will be impossible.
When ble_event_id is 0x1b, how...
Hello,
I'm having special SPI protocol which requires SPI Slave to toggle REDAY pin after every byte. I do test using 2 nRF52 boards. One is SPI master, another is slave...
