Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi!
I've quite wired problem with PWM based on NRF_TIMER.
When I modify CC value to adjust current value to desired value slowly (function is fired from outside event...
I have written application similar to ble_app_temp (posted by Ole Morten) and during the test I noticed that current consumption is extremly high. I used brand new coin battery...
I have writable characteristic on the server. As far as I understood there are at least two ways to access to its value: one using ble_evt_t and BLE_GATTS_EVT_WRITE another...
Hello,
i have seen here a extended version of Spi-Master driver:
devzone.nordicsemi.com/.../a00006.html
With funktions like:
-spi_master_send_recv();
spi_master_get_state...
I'm using the reference design for the WLCSP nRF51822 package, and I noticed that there are 2 pins (G3 and G4) that are listed as N.C. (No Connection) in the product specification...
Hi,
I am upgrading SDK from 5.2.0 to 6.0.0 working with SoftDevice 7 and I am facing a problem in relation with ANCS.
When I am pairing the phone (IOS 7) the first time...
Hi.
I have been trying to store data in flash by using pstorage.
What's the difference between pstorage_store and pstorage_update?
At the first time, I can save data...
Hi,
Is nRF51822 / S110 capable of simultaneously being in peripheral (connected slave) and broadcaster (broadcasting non-connectable ads) mode? The datasheet says both...
Hi,
I need to write data in to flash memory of the nRF51822 device.
I have tried to write data. When i checked memory address where i wrote data i could find that the...
In the nRF8001, after executing the command "ReadDynamicData"... I receive basically a bitstream with many bytes. The idea is to store it in order to be able to, later on...
I'm trying to write a flash buffer but am hitting a vexing error. To initialise the flash buffer (or rather a test initialisation which will hopefully become the flash buffer...
Hi
I would like to interface nRF8001 with a BeagleBone Black (BBB) an ARM cortex-A8 [1].
BBB has a SPI inteface and can support interrupt line input, and its running Linux...
I have an nRF51822 that I would like to be able to issue a soft-reset command under certain circumstances. I'm not using a softdevice in this version of code, so the other...
