I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
In the Release Notes of SDK 14.2 the following issue (for an emulated NRF52810 project) is mentioned :
*** Known Issues
****************
** BLE **
- When working...
Hi,
Is there any API in Softdevice S132 v5 production to set up advertising extension?
In migration notes of SoftDevice S140 v5 alpha3 I can find annotation:
A new...
I have read the nAN24-13 application note as well as the crystal selection portion of the nRF24LE1 and nRF24LU1 data sheets and I am still undecided about this crystal
https...
Our intention is to wake up the nRFLEI from power-down using the external interrupts, perform some actions and return to power-down. There are three external control signals...
Dear nordic employee
when I use the spim to send 1 byte address to read it's value(4 bytes)
nrf_drv_spi_transfer(&spi,headerBuffer,(uint8_t)headerLength,readBuffer,...
Hi,
We are trying to transmit a single byte over SPIM using easyDMA but our logic analyzer shows that 16 bits are being clocked out. The first 8 are our message and the...
Hi
I just test the new sdk 15.0
When I test the power of the demo project named "ble_app_hrs_freertos", I get the power table below:
No chage
810uA
...
Hello world.
After I have used this guy code.. KNN c++ . and good for implement it to my module nRF51822.
But if there's problem issue or not. because, there was an confusing...
HI Nordic,
I want to know whether the NRF52832 use the RC oscillator as the default source of HFCLK . I want to use the TIMER peripheral to do a precise duration measurement...
Hi all, I using 3 board NRF52 to demo remote provisioning mesh . But in client , I get debug terminal :
After client hang . Please tell me why and how to use correct
Good evening, I determined the numbers of clocks necessery to fire up an interrupt from an GPIOTE event. My debugger reports 1373 clocks ticks to go into and go back from...
Hi,
What is the maximum ATT MTU size for the BLE NUS?
While programming my BLE NUS server application I constantly ran into the problem that my MTU and length updates...
Hello,
am using the NRF52-DK softdevice 6.0.0 and NRF SDK 15.0.
I am working with PPI, GPIOTE and 2 timers (called timer1 and timer2) on nrf52832
Through the COMPARE...
Hi,
I am trying to use BlueZ in "Raspberry Pi 3B" to connect my 51822/52832 device.
My Hardware is Raspberry Pi 3 model B, and use internal bluetooth interface, the OS...
Hi Nordic gays guys,
After our 51822 firmware added the Service Changed characteristic.The Android OTA GATT_ERROR issue was solved.But there is a new problem in IOS.After...
