Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi,
Is it possible to send a advertisements for a single (or a fixed number of) Advertising Events? I need to control the number of Advertising Events "sent" for a mesh...
Hi, I'm looking to build a simple ANT+ application. My only asset for this project is a background in C/C++. I'll need to learn/relearn the basic electronics and protocol...
Hi Nordic,
I have an application that perfectly runs in the nrf51DK but that does not work in my custom board. In my custom board everything else works (i2c, leds lighting...
I understand that in order to trigger bonding procedure you need to read/write a secure characteristic.
I am using the nRF Connect application on IPhone and trying to see...
Hi all,
I need to take samples of a period of two periodic signals and made some DSP processing with both signals.
I need at least 64 to 128 samples per signals.
I...
Greetings,
In Bluetooth 5, there is a new mode of advertisement called periodic advertisements where the advertising device can periodically advertise over the 37 non-primary...
I have a design running on nRF51 that I'm evaluating to run on nRF52. One important characteristic I'm looking for is to store it for long period with a minimum power consumption...
Having some problems upgrading the PCA10056 to firmware 1.0.1 as stated in the getting started. After downloading the only file I found I can no longer connect to it.
Can...
I've been trying to use nRF52 (PCA10040 board) with SDK 12 to read data from max30102 through I2C.
I used non-blocking read and this is twi init function and event hander...
According to S130_SDS_v2.0, I can choose to return NRF_RADIO_SIGNAL_CALLBACK_ACTION_NONE after NRF_RADIO_CALLBACK_SIGNAL_TYPE_EXTEND_SUCCEEDED to stop extend more timeslots...
I want to trigger SAADC by PPI between RTC compare event and SAADC sample task. Is it possible?
In the SAADC example (SDK 12.2.0), a timer is implemented. In function nrf_drv_timer_extended_compare...
Hi!
Which project do i need to look at in order for 5 devices which are NFR52 to send data each other
There is only one center in multilink project and other devices dont...
hello there i want to use AES in nrf51.
i want to encrypt nrf51's advertisement data . and decrypt using android app.
i have some confusions
(1) should i use nordic's...
Hi,
I'm trying out the Zephyr os for the NRF51.
When I try the basic BLE example they work fine!
However when I try the sensor example which uses the i2c it falls...
Hello Nordic Forum!
I'm currently trying to load my firmware into my custom nRF52832 board without success. I'm using the nRF52DK (PCA10040) and the nrfjprog tool.
I...
