Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi I know i have just asked this question 2 days ago.
and it works 2 days ago.
Thanks to Terje Schjelderup, he solved my last similar question, and kindly reply my problem...
I've tried to use stdlib's random generate function.
and as usally all of the basic C language's random generate functions does, I've used srand with Seed based random...
Hi...
See my advertise_init function to add custom 128-bit UUID.As seen in the answer of this post devzone.nordicsemi.com/.../ i have changed uuid_type but still receiving...
i am using sdk 13.0.0 for nrf52840 running on IAR compiler. I am trying to create new project for AES but i am getting error as no definition for :
Error[Li005]: no definition...
Hi,
I am working on an application which sometimes needs to send a buffer of a couple of KB to a connected smartphone using the nordic uart service.
The function used...
Hello all,
I'm currently modifying my Analog Input circuit schematics to improve precision.
I'm adding after my voltage divider, an opamp as a voltage follower to ensure...
i have 3000 bytes of data placed in flash from 0x20000. i want to calculate hmac for the same data.First, can we calculate hmac for such huge data?If yes, then how can i calculate...
I'm using SD 110 and the PCA10001 board.
I make the call to:nrf_gpio_port_read(LED_1), where LED_1 is on, or high. This call always returns a 0. How can I read the state...
Hello!
I'm trying to advertise my custom service. After setting everything up, when calling ble_advertising_init I receive error 0x7.
static m_adv_uuids[] = {0x1523...
Hi,
I ported some SDK code into my device (SDK 10 adapted for S110v7x) where I can successfully Bond my device and use the Services I need (ANCS on my case). I have simplified...
Hello,
I have a project that I want to transfer it from nrf51 to nrf52 (the changes are from nrf51822 to nrf52832). I followed the migration guide. And now it debugs so...
Hi all.
I have phone with nrf Tollbox and central device with DFU, SD130 2.0.0, SDK11.
I would like flash application to central by OTA when I enter password in nrfToolbox...
Hi Nordic,
EDIT: I am using nrf51422, with S210 v5.0.0. Everything that is below is referring to ANT protocol
I want to know if the thing that I am planning to do is...
I download the example of multilink central (S130) into nrf51822 .The central transmit 20 bytes to peripheral interval 50ms sometimes will reset.Anybody know the bluetooth...
Hi guys,
I have the NRF52-DK and want to power only the NRF52. So basically, I want to power it over VDD_nRF.
When I power my DK with a battery and then measure my current...
