before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
It's NRF52832 and NRF52810.
The BLE connection process is to establish a physical connection first and then discover the service to obtain the characteristic word information...
Hi,
For my application, I would like to have multiple watchdog timers. I am measuring several sensors (I want one short-term watchdog timer to be fed in this loop, pause...
I am new with nrf52 DK . I was trying to work with SPI code example given in the nordic example folder but its not working . I am trying to transfer the accellero/ gyro data...
I am using SDK 15.0 with the Nordic NRF52840 development board. I wrote my own custom bootloader using CDC ACM as the transport. I am using app_usbd_cdc_acm_read_any to read...
Hello All,
Is there any already available example of OLED display interfacing with nRF52DK, pca10040, SDK 14.1 in Segger Embedded studio?
I am working on a project...
Hi，
I want to measure the time of two signals to calculate the speed and sent the data with BLE. I find the SD effect the GPIOTE_interrupt sometimes, when I try to use GPIOTE...
I an trying to locate and download some programming examples. For instance the BLE Blinky application
ble_app_blinky_c says it is in the EXAMPLE FOLDER, no matter where...
Our project uses nRF52832, and the bluetooth connection has two modes as follows:
one is low-power standby mode connection interval=1000ms;
One is data transmission mode...
We have recently ported our application from SDK 12.2 to SDK 14.2. The application is very power sensitive and uses a high connection interval and slave latency to minimise...
We have a project running based on the SDK 14.1 on a nRF52DK with S132 5.0. The used bootloader works as expected and also an update of the bootloader works properly.
After...
Developing medical sensors for medical institutions according to legislation ( us-fcc.app.box.com/.../8acz9o1cah6eqqpm2q3ktvfkkqt37v7p) in the 2340-2400 MHz band - nrf52 seems...
Dear Sir,
I want to access two slaves viz. MAX30205 & LIS3DH by using nrf52832. The problem is, as per the datasheet the values of the pull up resistors required by both...
Cannot get nRF Sniffer version 2 (beta) to work properly with nRF52 DK running the sniffer_pca10040_51296aa.hex:
Windows 7 64-bit
nRF Sniffer 2.0.0-1.beta
Wireshark...
