I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
I want to send images to my arduino from an app to nrf8001 and then display it on my device. Is nrf8001 made to only work in 20-byte wide receive buffer? Can it receive more...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hello all,
after a long period of trial and error I come for advice. I use the NRF24L01+ module with a slightly modified NRF24-library based on the work of MikeM ( www...
Hello,
I've recently bought a nRF905 development kit. From the nDP soft, i cannot detect my nrf905 EVBOARD.
The following driver is installed : "nRF2401 FS USB DEMO...
Good morning,
I just finished my circuit with nrf8001 + balun/antenna.
What is the process to have it review by Nordic?
Sorry for this question, I'm pretty new to PCB...
Hi
I would like to develop an application for the nrf51822 with a static passkey that connects with linux. The example "nRF51-ble-app-uart-static-passkey" gives a great...
Hi,
I would like to use Random number generator when soft device enabled. I have seen random generator example, but I can not use the same when soft device is enabled....
I was considering the following possibility, using an nrf51882 module or another module to receive ble advertisements. I'm pretty sure this is possible. Using the internel...
please, help me ㅠ_ㅠ
it mades me crazy
My PC is Windows 8.1 & 64 bit.
I try to install / repair / change SDK (6.1.0 version, 6.0.0 version, 4.4.1 version)...
I have achieved the demo referring to the IoT SDK and can control the lights on the nRF51 DK through the Firefox browser with Copper plgu-in in the LAN.Recently I want to...
Hi,
I interested in a simple system of a master and slave nrf2460. But how many of these systems would happily coexist in a the same room?
Thanks
Senthil
The Enhanced ShockBurst PTX Project just inits the ESB and start transmitting without ever configing either of the 16MHz or 32kHz clocks (none that I can see at least).
...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
hi.I have a question about synchronization. In main loop, there is a function sd_app_event_wait() which blocks until ble event from softdevice call occurs, so I want to put...
