Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Today I read about the new nrf52810 and I want to know about its main differences with the nrf52832.
I see a lower power consumption for the 52810 vs 52832 and no NFC on...
Hi
Currently I try to migrate my software project (with SDK14.2, S132 (5.0.0), arm-gcc toolchain ) from nRF52832 to nRF52810 (with SDK14.2, S112 (5.1.0), arm-gcc toolchain...
Hello everyone, I am a beginner in the use of Nordic Thingy: 52. I would like some help trying to reprogram the Nordic Thingy module. After a programming error of the Thingy...
HI,
I am unable to communicate between a SDK 8.0 based nRF51822 sender and SDK 14 based NRF52832 receiver.
The data rate of the SDK 8.0 sender is 250 KBits/sec, whereas...
Hi,
Can someone help me with question on SPI?
What is the difference between SPIM and SPI? They seem to have different clocks
Also in the SPIM section, the frequency...
Hi there,
I am developing a BLE dongle on nrf51822. There is no external 32.768KHz crystal oscillator on my customized board(only has an external 16MHz oscillator)....
hi,
I need to know how to use "power on reset". From the reference document, I can understand BOR and POFWARN. But the POWER ON RESET, I could not get any idea.
1. POR...
i have project with nRf51822 and uart. i use uart fifo in Uart_app_ble example sdk11. now i need disable or enable Rx, TX.i tried this function :
NRF_UART0->TASKS_STARTRX...
Hi,
Has anyone successfully used semaphores/mutex implementations of FreeRTOS?
The code I am working on is based on the FreeRTOS HRS SDK example. I am looking to add a...
Trying to compile using the on-line Mbed compiler. I keep getting cannot find "nrf.perhiperals.h", and I cannot locate it either.
Possible someone can point me in the right...
Hello.
I'm using Tielen Marjle STM32 library for nrf24l01+ ( https://stm32f4-discovery.net/2014/06/library-17-nrf24l01-stm32f4xx/ ) which worked great till now, when I...
This is related to the new nordic dev zone, not nrf connect, but there is no dropdown option for it.
After signing into the new nordic dev zone for the first time since...
Hi there,
I'm using ASUS RT-AC1900P router with IPv6 DHCPv6 on. RPi gest its own IP with prefix specified in router but interface wpan0 (wpantund) not. I have configured...
just like the title.
I'm using sd_radio_session_open APIs very similar with
https://github.com/nordic-auko/nRF5-ble-timesync-demo
and add data uploading by gatt.
using...
