This feature used to be helpful pre version 2.7 or so, but has persisted as an issue since then. All of the configs in any *.conf are all underlined and have this phrase when...
Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hello,
Bootloader jump on DFU_BANK_0_REGION_START.
DFU_BANK_0_REGION_START = CODE_REGION_1_START = SD_SIZE_GET(MBR_SIZE) but if i watch value, debugger says it's 0x3008...
Hello,
I am using the nRF52 along with SDK 9.0.2. I have used both the ble_app_uart code and the twi_master_slave code to send data from a sensor over bluetooth to the...
Can anyone explain the difference to me between the two SDKs?
it seems I can use them both for nRF52 development?
they both support the S132 soft device
Which...
i use nrf52 DK as master and configure ads1292 breakout as slave. I have try the loopback example which works properly. I write the sample spi code based on spi_master_with_slave...
ble_app_uart_s110_pca10028
i need function is press button to erase bonding information, then use App to connect and bonding.
How to implement this function? could you...
Hi All,
I'm working with the NRF52 Preview DK, with SDK V 0.92.
I've been looking at and tweaking the SPI_Master tutorial found under /examples/peripheral/spi_master...
I'm exploring the possibility of using an nRF51 for a simple device which must take data samples on a fixed clock and push them to a remote client. The issue I'm investigating...
Even though the documentation suggests that there are 3 RTCs (RTC0, RTC1 and RTC2) and the file nrf52.h has a declaration for the RTC2 peripleral, I am not able to use it...
Hello,
I need a bigger bootloader so if i modify ld file line from
FLASH (rx) : ORIGIN = 0x7A000, LENGTH = 0x4000
to
FLASH (rx) : ORIGIN = 0x00077000, LENGTH = 0x8000...
link text from this post i am generating interrupt using button 3. when i push my button,interrupt generates,LED turn on. but after turning on LED, i want to clear interrupt...
I am using SDK 9 on an nRF51 device with the S110 SoftDevice. I am aware of issues using the the PWM library from SDK 9. I need to use the PWM functionality but would like...
Hi,
i tried to modify app_pwm to add an additional timer, since i'm out of timers.
so at the end of app_pwm_init i added
nrf_drv_timer_compare(p_instance->p_timer...
Does NFC has something like an unique adress?
Because the nfc examples in the sdk detect all nfc devices. But I would like to detect only predefined devices.
Or is there...
I seem to be getting correlation on addresses
I running the radio transmitter and receiver examples provided in the nRF5 v11 SDK. However, I am observing still some unexpected...
