Hi There,
I am using a nRF52840DK board to experiment with NFC Tag technology.
I started with the "Writable_ndef" example inside the nRFConnect, and it works.
I wrote...
Where can I obtain the security certificates (e.g., client certificate/private key) needed for TLS authentication with nRF Cloud? - Are these generated during device onboarding...
I plan to use my own SIM card (not from Ibasis). Could you clarify how to register the device in nRF Cloud to enable A-GPS services? - Should I link the device’s IMEI or ICCID...
Hello, I am developing nRF5340, the project is pre-production. I am getting a issue with BLE power consumption, when I turned BLE on, the current is about 9uA. with BLE beacon...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi
I am writing an application that requires bonding/paring stuffs and face a problem as below
The maximum bonds that my device can manage is 2. When these 2 slots are...
Hi
I use nRF6310 and PCA10005 to develop BLE project. When entering DTM tab, I cannot find the motherboard on "set up on".
DTM.jpg
My hardware is:
motherboard: nRF6310...
Dear Support,
we have done some technical question
About the N5 module of Dynastream (with nRF51422) we would like to program the software placed into the application...
my android program add many nRF51822 devices mac adress to a file in my android device.So I can count number of connected nRF51822 to my android device with bluetooth low...
Hi,all.i want to integrate ble_dtm(6310 board) to ble_proximity(pca1001 board).Can someone give me advise? i run ble_dtm on my board,and cannot find "Nordic_DTM" when i scan...
Hi,all.i want to construct our product test system.i follow AN34 page6 (figure 2) to do this.i have a question: DUT and nRF DK module run same firmware ? if correct,when nRF...
Hi,
In my application, I would like to take some action, when the bonding is removed from the phone.
At the moment I'm using static key for bonding and I see that BLE_GAP_EVT_SEC_PARAMS_REQUEST...
I'm using SDK 7.1, SD310 2.0.1, MCP 3.8.0.7
I have two versions of a board with the nRF51. Some of them have the 32kHz crystal and some don't. In my application I have...
Hello,
I am working on an application based on the "Motor control example". However instead of just setting two different values for the duty cycle I am trying to either...
Hello,
I have started to study your UART to/from BLE sample but after reading the following post ...
devzone.nordicsemi.com/.../
... I have a big doubts.
Due to...
Dear Nordic,
I am using a pretty much unmodified version of the BLE HID Keyboard example from the Nordic BLE SDK (straight of github).
I only modified pins, and disabled...
In Short: How to get status wether noticiations are enabled or not? Where is this stored?
Hello,
I would like my peripheral to start/stop a timer that does measurements...
