I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
on the nrf52832 I am configuring pin 10 as an input. There is either 0 or 3.1V on the pin depending on whether a charger is connected to the board.
When I read the state...
Just stumbled upon this:
#define TIMER_PRESCALER_PRESCALER_Msk (0xFUL << TIMER_PRESCALER_PRESCALER_Pos) /*!< Bit mask of PRESCALER field. */
Should be
#define TIMER_PRESCALER_PRESCALER_Msk...
I am working on project where I am storing and reading data from an SD card. During the initialization, I would like to print the full contents of the root directory - "/...
Hello,
I have a problem through which unfortunately I'm not able to come across alone. I'm using nRF52832 with softdevice and UART central example from SDK14.2 (..\examples...
I'm using nRF52840-PDK. I created a custom ble service following this tutorial ( github.com/.../custom_ble_service_example) and sent my sensor data over bluetooth. Now I'm...
Hi ,
I am trying to disconnect a connected central (phone) by calling sd_ble_gap_disconnect from my nrf52 configured in multiperipheral mode. . The disconnect call returns...
I am trying to time a capacitor discharge through different resistance sensors for greater resolution than an ADC. I did this using the GPIO functions initially but the SD...
Hi,
Is it possible to use Segger Embedded Studio with nRF51?
I see on your web site it's supported with SDK 14 or greater but this SDK is only for nRF52.
My product...
I have problems with my custom board.
I developed the firmware with the nrf52840-PDK and there the firmware runs standalone (with RTT connected and without) or when debugged...
Hello
I am working on nrf52382,sdk11,softdevice 2.0.
/cfs-file/__key/support-attachments/beef5d1b77644c448dabff31668f3a47-fd3fce63fa6d4ddfa73158194e4d87c3/battery_5F00_pins...
Hello,
I am writting a batch script to flash a PCA10056.I use it to flash the softdevice, the bootloader and my application.
The script works well and flash the device...
Here NRF52 TX pin is connected to Battery to measure voltage Level. i am using NRF52 with SDK 11 and s132 soft device.
Here is my Schematics
here BATTERY is connected...
Hi
I am working with the twi_scanner_pca10056 example found in the SDK. Using a oscilloscope I can detect the logging messages on pin P0.01, even though sdt_config.h defines...
