I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Hello -
I'd like to make sure my RAM/ROM layout for the nRF51822_XXACis OK - if someone has a minute to double-check it that'd be great.
I started with the "nRF51822 Beacon...
Has anyone been able to get the examples to work on PCA10028?
I went through the following steps:
Used nRFgo Studio to flash in s110_nrf51822_7.1.0_softdevice.hex
Downloaded...
Hi,
Could I write or update flash without softdevice ?
Due to I must update softdevice on our product, but it doesn't have any JTAG Interface,
so, I want to use our application...
Hi,
I want to start TIMER1 by a GPIO_TE.
When the program enter the TIMER1_IRQHandler(), I want to disable the ppi.
And when the program leave the TIMER1_IRQHandler(),...
Hi,
I'm on OSX, and I'm having problems where the first service calls I make on my own device fails but work fine on the second generation Nordic development board.
...
In the changelog for 7.1.0 is says:
"This version deprecates all previous 7.x.x versions"
But in the compatibility matrix, it seems like 7.1.0 is only supported by revision...
i had used flash manager that is in BLE libraries to store datas for persistent storage. but it seems can't work after i enable the softdevice. so i try to use pstorage, i...
Hi support !
In my current application, I use nRF24L01+.
I want to change this nRF24L01+ for a nRF51422 to add BLE connectivity.
So, I've started my development with...
I'm using SDK 7.1, PCA10028 eval board, SD110 7.1, MCP 3.6.0.8331
I have 2 characteristics, and both are 32 bytes long. When I try a "Write Long" from the MCP a
BLE_EVT_USER_MEM_REQUEST...
Hi,
Merry Christmas!
I have a question about pstorage_store.
Actually, I want to store some data in the memory. Each piece of data has its own size (between 1 byte to...
Can I config AIN0 and AIN7 as the input pins of ADC, and config P0.01 and P0.02 as TWI, and config P0.03 and P0.04 as GPIO?
Or I must config ALL AIN PINS as ADC?
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
