Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hi, I use ble sniffer 2.0 beta with nrf51 (pca_10031_51296aa.hex). Is there a sniffer api documentation with description of the UART protocol (as with sniffer 1.0.1)?
Good morning everyone,
I am facing a weird problem concerning the use of the UART service.
I am currently using the NRF52832DK to develop an application. In a nutshell...
Hi Forum,
I am working on nRF52840 THREAD sleepy node and facing an issue in deep sleep mode. The current consumption in deep sleep mode is more-around 60-70 micro Amp...
Hello guys!
Are there any difference in using FDS library with a nRF52832 or with nRF52810?
I will explain.
I'm using a FDS for writing/reading to flash for 2 months...
(I've seen several other posts mentioning similar issues, but many of them haven't resolved or found a solution that seems to apply in my case.)
I have a custom board that...
Hi,
I have a simple and basic question. it may be chilly. the internal flash memory can store the data, but the question is it has stored as byte per address or word per...
I am using a nRF52840 chip in a custom board. I will be using all the SAADC channels, as well as 4 SPI connected ADCs.
The board itself will likely be powered for days at...
Hi !
I am using NRF52DK and I want send some daat with BLE. I have to send 800 bytes in BLE by packages of 25. So I tried this :
BUT when I look my uart terminal, I...
Hi, DevZone,
I am trying connect nRF52480 Preview DK and an Arduino UNO CAN Bus shield.
What I did is:
1) I directly hook CAN Bus shield on the top of nRF52480 Preview...
Hi Nordic,
I started from an empty project with peripherial control first, the code size is about 12KB. Then after adding peer manager and related code(fstorage, fds and...
Hello,
I build a custom board with Nrf52832 , to drive Relays , all works without load , no problem for drive the output.
When i put a load sometimes my device disconnect...
what are the total number of devices that can be connected to nrf24 ?
I would like to make one transmitter and rest of all as recievers without acknowledgment will it be...
Hi,
We are trying to use GPIOTE / PPI to turn a MOSFET on A microseconds after an event clears a timer and to turn it off B microseconds afterwards.
It is easy to do...