Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
i tried to find an example with SPI which describes the connection between two nrf24LE1, one as master and one as slave, but i could not find anything. I need the following...
Trying the ATT_MTU Thourughput Example with SoftDevice:
nRF5_SDK_13.0.0-1.alpha_055eef3/components/softdevice/s140/hex/s140_nrf52840_5.0.0-1.alpha_softdevice.hex
on...
Hi, I just want to know,
Is it possible to develop a device that advertise normally and be connected by mobile, but the device must always send the eddystone-format advertising...
I'm interested in adopting nRF52840 as a mesh networking + Beacon device. It is my understanding that the Nordic SDK for mesh will only be released after Bluetooth SIG releases...
hello everyone:
I work IPv6 over BLE example on both Raspberry pi ,this pic is 6LN (CoAP Server)sending IPv6 over BLE packets to 6LBR(CoAP client) and I use tcpdump to...
Hi,
I'm testing the multi-link functionality.
I want to manage the connections with connection handler.
But, p_gap_evt->conn_handle passed thru on_ble_evt(); and p_ble_nus_evt...
Is it possible to setup the nrf52 with the HRS profile along with UART. I'd like to send heart rate date along with UART messages.
I'd also like to have an android app...
Hi all,
I have need to create BLE device with ability to securely store private keys and change those. According to presentation from ARM with assistance of CryptoCell and...
Hello, I wanna know where I can download it, if there is one at all?
I want both schmatic and pcb library file. I thought I can substitute and "make due" with nrf52832...
I'm using nRF52 + SDK11.0.0 + s132. I'm following this tutorial. I am able to build from the command line and from Eclipse just successfully. However, Eclipse is unable to...
Hi
I'm using nrf51822 with soft device 11.0 & want to read a 12 volt digital signal for this I'm converting 12v to 3v3 (4.5 & 1.5 Kohm Resistor) using voltage divider ckt...
I am using nrf51822 with soft device s130.I used sd_app_evt_wait() to enter the sleep mode and i disabled all the peripherals before enabling sleep mode.According to the datasheet...
I can't understand concept of control point..
Is it just one of charateristics?
So what are differences with other charateristics?
I heard that control point can...
I'm not sure if this question has been asked here before, but I couldnt find an existing answer...
I know that flash memory only has a relatively limited number of write...
What is the MDK? I am using Eclipse and GCC on Linux with the GNU ARM plugin for Eclipse. I need to upgrade from SDK12.0 to get the workaround for errata 108.
The release...
