Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Lets say I have 200 bytes of data that I want to store in flash. So, I request a 200-byte block.
In order to store, the area has to be cleared first. As far as I understand...
Using the nRF51-multi-role-conn-observer-advertiser-master project to test timeslotting I have encountered two issues (Softdevice s110 7.1)
Issue #1: Repetition of advertisement...
Now, I need two function add my project (On BLE stack).
Distinguish long/short press at same button.
2.device and master synchronous time.
No.1 question is...
Hi
We have custom nrf51822 board.
in that we have nor flash which is spi compatible.
so in order to read device id i used spi_master sample source code.
i am able...
Hello,
I'll explain my code:
NRF51 takes samples of a sensor every 10 minutes. In addition, softdevice S110 is used... An user can connect at any time, so advertising...
I am trying to implement frequency counting on nRF51822 by counting number of pulses in a given period. I create a PPI channel with a GPIOTE event on rising edge linked to...
Hi,
is it possible to mount a nRF51822 in an aluminum enclosure and use ble?
I am looking for a range of up to ten meters in an open area.
Is that possible or will the...
there is no bin folder under C:\Program Files (x86)\Nordic Semiconductor\nrf51 as described in the docs.
so I'm not sure where the nrfjprog.exe should be
I am trying to better understand how the nRF51422 handles sqrt(n) coming from C in Keil?
Can anyone explain, or link to resources which do? I am having difficulty finding...
Hi all,
It is possible to install and develop projects using 2 SDK versions simultaneously?
nrf51 SDK will be used in the current project and nrf52 SDK will be used for...
I want to do 2 things with the nRF51822 beacons
Add an ADC output to the advertising packet (non-connectable mode)
Set the advertising interval to 1 hour or longer...
I measured the current drawn by the nRF51822 beacon with its default beacon code. The current was about 1 mA which was same as in another thread
The suggested solution...
We have been manufacturing for a while with the nRF51822, Revision 2, and WLCSP package and build code D0 (D0 is what Nordic recommended me to spec to contract manufacturers...
Hi all,
I have application that read analog level and send the data with connection interval of 10 ms and 0 dBm, how can i calculate the current consumption of BLE? i read...
Hi
I want to use Printf() in the DT2 but it cannot output msg to terminal.
I used hal_uart_config() to config UART TX/RX/Baudrate... in mail.c then
call hal_uart_put_str...
