I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
I have Stlink v2 programmer and I would like to use it to flash hex file into my nrf52832 I read a lot of threads about using tools like openocd but none was helpful, I think...
I'm attempting to build the ble_app_hids_keyboard example from sdk 14 using gcc and the compiler is throwing the error "No such file or directory", but the file is there and...
I have problem on SoftDevice V6.0.0(nrf52832) scan_start/stop. modified ble_app_blinky_c(ble_central) 1. app_timer add (20ms cyclic) 2. app_timer handler, run sd_ble_gap_scan_start...
Hi
The 'ble_app_multiperipheral_pca10056_s140' example for the nRF52840 has an 'LED' characteristic under which there is a "Nordic LED Button Service"
The value...
Hi,
I've defined:
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE 120 (in sdk_config.h)
I get "Insufficient RAM allocated for the SoftDevice" in nrf_sdh_ble_enable
nrf_sdh_ble_enable...
Hi everyone, I'm looking to buy nRF52840 SoC for my thesis but I'm surprised that none are yet available from Farnell, Mouser or Digikey ... I found few chips on Symmetry...
Dear Engineer,
We are working on 52840 usb dfu,program softdevice s140_6.0,
and usb secure bootloader,
evaluate board is pca10056,v0.9.0
Led1,led3 turn on once load...
I am very new to ARM controllers. All of my experience is with Atmel family, which I've been using for years.
I just got the nRF52 Development board and have loaded several...
Why do the version numbers have to be as follows for a merged hex file to be able to exit the dfu mode when flashed externally as a combined hex file (SD +BL + BL settings...
With the BT 5 extensions, is it now possible for BLE Peripherals to communicate with each other without a Central ?
In the envisaged application, one node would be the central...
Hello,
my problem is reproducable with this Setup:
nRF5-DK with ble_blinky_example (central)
nRF5-DK with ble_blinky_example (peripheral)
Press Button1 immediately...
Hi,
We are using nrf8240 SDK15 and need to convert soft image which is in hex format to binary format. Tried using 'arm-none-eabi-objcopy' for this. It converts 424kbytes...
Hello Nordic team,
I am developing a proprietary radio protocol and i am using aes ccm peripheral for encryption (i am a begginer). The packets seem to be correctly encrypted...
Hi,
Can you guide as to how to set up an proxy node that participates in mesh activities as well as connects with an non mesh device (viz Mobile) from time to get data from...
I’ve been working in a small group to use the advertising extensions in BT5 to send 12 hours of temperature measurements in one advertising packets. We’ve been developing...
