SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
So I suspect there is a very simple answer to this, but a couple days of much reading and searching haven't led me to a very clear answer.
My setup: Galaxy S3 (Android...
I'm trying to move data over the uart characteristic. I followed the guidelines here devzone.nordicsemi.com/.../
In the main loop I am calling sd_ble_gatts_hvx until it...
I'm working with an nrf51822 with the s110 softdevice. So I'm trying to read an analog signal from multiple pins. My program will run fine for quite some time. Eventually...
Hey guys,
I need to record many time interval ?, can i generate system time and use it to record all of my time intervals?
If I want to send all of the time intervals...
The gcc compiler is gcc-arm-none-eabi-4_9-2015q2.
The make version is GNU Make 4.0 (Build for arm-unknown-linux-gnueabihf).
The error message is:
... arm-none-eabi...
So I'm using the spi_master.c from SDK 6.1 to communicate with an LCD driver. I'm using an nrf51822 with s110 softdevice. My system has been sporadically hardfaulting on me...
Hello all,
I have found closed topics here with similar names ( devzone.nordicsemi.com/.../ etc.) but my question is about adding the characteristic with encryption.
My...
Hi,
I'm trying to transition my application from SDK 7.2.0 to SDK_9.0.0 and am having some issues when including ble_advdata.h compiling with gcc:
In file included from...
Hello,
I know I'm not supposed to use TIMER1 with IRQ 0 when using a SoftDevice but I want to try anyway :) I want to do some bit banging with timing that is timing sensitive...
I am trying to program custom boards with the NRF51822 using an ARM-Flasher with no success. Using J-Flash I can connect to the device properly, program and verify the hex...
What could be the reason for?
Couldn't find any error descriptions.
Using Laird BL620US with newest FW v12.4.14
Error occurs as a response to 'scan start 1000 0 0'...
According to the *.map file the .bss (RAM) usage for my Application is 0x16b8 or 5816 bytes. This is obviously a very high RAM Application, likely due to the abundance of...
Hello Nordic,
I am working on [nrf51822 custom board+SDK8.0.0+SD110]. I need to test button press bouncing and de-bouncing, how it works on the board ? I found one example...
Hi,
is it possible to use this module from LAIRD in connection to the nordic SDK - i installed the softdevice hex but the hrs example for s110 is not running properly ...
Hi.
My nRF51822-mKIT, when attached to the USB port, don't flashes the green LED nor the drive appear on Windows explorer.
It's possible that mbed loader was corrupted...
