Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I would like to use the COMP capabilities.
The input is from NRF_SAADC_INPUT_AIN1.
The input voltage is 0.1-0.8V.
I would like to get interrupt every time we change...
Hello everyone,
I use sdk14.2 softdevice S132. I want to write "uint8_t some_array [7] = {0x00,0x01,0x02,0x03,0x04,0x05,0x06};" with use fds_write and read the array from...
When using BLE_GATTS_VLOC_USER to store multi-word characteristic values that are updated by application code, what is the recommended way to prevent a partially updated value...
I am working with ble_app_uart code, in that I am trying to send continuous data over BLE. But the BLE getting disconnected while sending large data.
So I planned to have...
Hi,
We are using nrf51822 QFAAH00 with SDK 110 v8.1.0 in our project, the application will hangs or not work when control stuck at address 0x6b0 (sometimes at 0x640) programmer...
Hi all.
I've followed as much information i can find regarding RTT. I understand that it was build in to the SDK after 11 or so and I followed the guides on https://infocenter...
I use the connection event extension, but there are several concepts that I am not very clear.
Software:S132 v5.0 . SDK14.1.0 nRF52810
Goal: I need to use high throughput...
my TWI device sensor, both its writing and reading address is 0x55. This seems weird for library of nRF since the last bit should be set as 0 for transmission and 1 for receiving...
hi Engineers!
the questions - is it possible to implement multi advertising (need two) broadcasters with different advertising data use SD 140-6 (nRF52840) ?
in the new...
Our Project is based on the multiprotocol THREAD BLE dynamic example.
We have the BLE DFU also as part of our project and it is working.
We now need to add the flash storage...
Hello :)
I have a question about the timing of sending a bluetooth write request. I am using two nrf52 developement kits, one as master and one as slave. From my master...
I am porting to SDK15 and this is the error I am getting:
../../../main.c: In function 'ble_stack_init': ../../../main.c:2746:2: error: unknown type name 'nrf_clock_lf_cfg_t...
Hi,
While customising code for my application, I noticed that in on_connect method of ble_nus.c, in the p_client we set is_notification_enabled = true after checking ble_srv_is_notification_enabled...
Hi there,
I have two type nRF52 DK, pca10040 and pca10056. I know that pca10040's maximum txpower is 4dBm and pca10056's maximum txpower is 8dBm, and both boards have CR2032...
