We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
In SDK 15.0.0\modules\nrfx\soc\nrfx_irqs_nrf52810.h, at line 65,( link ) it defines a SPI1 compenent:
But 52810 spec( link ) mentions only SPI0.
Is the code file correct...
Hello everyone,
So I'm trying to maybe start get going with the NRF52832 platform but every time I try I get stuck with it.
In this example I'd like to use different...
Hello, I would like to know if there is there a "global" sdk_config.h file which has #defines for all modules? Ie, if I make my own project, and use this file, all I would...
Hi!
I would like create my own application of BLE Mesh on nRF52832, I had gone through the Light switch example and understood some basic concepts and now i'm thinking start...
Hi,
I tried to erase the bound and start another pairing procedure without rebooting my device. I was not able to remove the bond correctly. The system hangs when I call...
Hi,
I had Completed secure OTA in my custom board (RL nRf51822 A1).
We have to PCBs. 1). Old Design 2). New Design
1). Old Design: We have connected relay on pin(p6...
Hi all,
In our program calling app_usbd_cdc_acm_write() a single time does not directly send a message to the terminal program (Teraterm). Even Teraterm is not getting connected...
hi, everyone:
I want to use the experimental_bootloader_secure_serial to update firmware with UART, disable the hardware flow control.
how to reset system when application...
Hello,I have couple of nRF52832 boards,nrf5_SDK_for_Mesh_v0.9.2-Alpha.
I want to test the light control example,but some problem bother me.
It can not work normaly.The...
Any chance someone have develop a iOS (Objective-C / Swift) library to wrapping Nordic DFU Protocol?
I'm aware of the availability of the source code of nRFToolBox ( github...
When is the next version of nRF52840 coming out (or available through a distributor in Switzerland)? In an earlier version of this chip, we were unable to link the micro USB...
After setting up the tool chain and confirm it is compiling correctly by flashing the Proximity build into the dev kit PCA10040 and confirmed with the Android App it is fully...
Hi,
I am develope a ble device use nrf51822 , when I use a Android app to connect the device without start a scan , only use the mac address to connect the device , I cann;t...
