Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi,
Does the .hex file for V7.1.0 include the master boot record? I'm writing a JLink script to flash it and I'm trying to figure out, once converted to a binary file,...
I have the PCA 10028 Board. I would like to add a characteristic on an already existing service.
In the nAN-36 I see, what is necessary to set up service and characteristic...
Dear Forum,
I just unwrapped my new nRF51 DK board and already played with some mbed example programs which worked beautifully! So first of all - thank you Nordic & mbed...
What capacitors would you recomend for this 16MHz Quartz http://www.jauch.de/ablage/med_00000848_1411137106_JXS32-180914.pdf to ensure 40ppm frequency tolerance for nrf51822...
I read the following but was not able to use it to resolve my problem.
devzone.nordicsemi.com/.../
bootloader.hex
bootloader_settings.hex
The bootloader address...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hello,
I would like to use the PCA10031 Dongle as the peripheral with the multilink examples. I will be wiring up a button to the available GPIO and using this for a space...
I want to use to set the UUID in my Nordic device as following:
Base UUID:
{0x80, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,...
hi.
I refer at the example find here link text .
i want to transmit with Advertising, as the temperature is transmitted in the example, data from some sensors .
But in...
I'm trying to port the HRS example using S110 Softdevice and SDK 7.1.0 to IAR 7.10 on the pca10028 board.
I've created an IAR project which uses the same files as the Keil...
Hi everyone,
I am trying to create a file in sd card but it is not creating.But i can read a file from sdhc card of type .txt,.c,etc with nordic evolution board nrf51822...
Hi all -
I want to use the device manager (SDK 7.1.0, SD110) to do a simple nRF51822 implementation where after the first bonding happens, and is stored in flash, the nRF51822...
Hi
I have a board with some extra bits and pieces hanging off the SWD lines.
This means the SWD needs to run at a lower speed (500kHz or less). At the lower speed, Kiel...
Hi,
I'm trying to build my IAR project but it's not clear to me what I should link against to resolve symbols referenced by the soft device headers.
Thanks,
Kenn...
Hello,
Is there any reference designs / documentation or ideas on how we can wake up NRF51 when there is radio activity on a specific frequency ?
In our design, we need...
