Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hello I'm a beginner and I try to use the DFU. I use the documentation and I can send my init packet without any problem. But when I try to send my Firmware I have 2 problems...
Hi,
Our system is based on the nrf52832 with SDK BLE_2.0.1 for the mesh. I have few queries as per below,
1)It would be great if you could suggest any vendor who is working...
When Going into Sleep, I see peaks of 12mA every 30ms (see image) I'm assuming I can adjust that changing the connection interval settings. I have my Connection intervals...
I'm having some issues with the freeRTOS example in SDK 15. I've always seemed to find a hardfault which limits the MTU size to 176. Now when I try and set the connection...
Hi,
I have a question regarding fast/slow advertising
I'd like to advertise for 180s using a 100ms interval, then switch to a 1s interval, preferably for ever. I set...
I would like to use ADXL335 accelerometer in this nrf52832 custom kit Hackable . I don't have a J-Link but i have this custom programmer Bumpy which is based on the Black...
Hi,
How can wake my nrf52832 based module from system off sleep mode. i am using ' nrf_pwr_mgmt_shutdown()' / ' sd_power_system_off (); 'function to put the device into...
softdevice 6.0.0 SDK15.0.0 How do I use ble_app_hrs sample code add buttonless_dfu function? I flow the steps, but I am fail. 1. In ble_app_hrs project... add nRF_DFU folder...
Hi Support team,
In this application note, solder paste type 4 has 25 to 45 micron particle size range while IPC J-STD-005 as attached stated type 4 has 80% Minimum between...
hi.
I used mergehex.exe to combine the hex of softdevice, bootloader, and application into one, but the board is in DFU state and the application does not start.
I am...
Hi! I'm developing on nRF51 with SDK 11 and trying to extend our application with buttonless BLE DFU support. Due to limited flash memory, we could only use single bank ble...
The website is broken for me, and I see a sequence of orange pop-up messages saying "An error occurred. Please try again or contact your administrator."
When I use master control panel to scan ibeacn, I find "Complete Local Name" in below picture,
How to set the "Complete local name" ?
I heard someone says set in the...
Hello,
I've now been looking for a while but haven't yet found anything working to programmatically unwind the call stack when working with the nRF51 or nRF52.
Basically...
