Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hello everybody
I am working with the Raytac BLE Module "MDBT40", which is based on nrf51822.
And I am testing example project "ble_app_uart" in the SDK6.1.0 now.
...
I would like to confirm my understanding of Problem sending 6 bytes to multiple services using sd_ble_gatts_hvx
I use nrf52832 sdk13.0.0
BLE SPI is master. I dropped...
Hello,
I connected the nrf module to jlink as described:
• vdd(nrf)-----3.3V
• gnd(nrf)-----gnd
• SDO(nrf)-----SWDIO(jlink)
• SCLK(nrf)-----SWCLK(jlink)
• 3.3V...
I've run into some interesting behaviour in my code and wanted to see if anyone can clarify for me. It seems as though the SPIS module doesn't set the MISO pin as high impedance...
Hello,
I built a simple I2C application for the LMP91000 and I was successfully able to configure it to read the status register.
However, I tested to see if I could...
Hi,
I used to use an imitated Jlink debugger to program/debug my target board(one Nrf51822 on it)
There are pins connection between them,it works just fine.
Now I...
I aslo read other question about sd_ble_uuid_encode .
But my problem is different from it.
I use nrf52832 and DK board.
I made my application from ble-app-template...
Hello,
I want to define a writable payload section and a static payload section (not writable) in one tag is this possible?
I have now implemented it like this, but...
While reviewing the Thread DFU examples I saw that Nordic ported the IoT CoAP library to thread. Is it possible to use other IoT libraries with some modification? Obviously...
I am creating a BLE peripheral device which I want to test using the automated testing feature of NRF Connect. I have connected a android phone to my windows PC and the phone...
Hi.
I'm trying to send data through L2CAP from Cypress BLE evaluation board to nrf51822 chip.
It seems that Nordic's API for L2CAP is much simpler than Cypress', but I...
I noticed some suggestions to add Static Passkey.
I have 10040 nrf52832 sdk13.0.0 s132
The server has no IO, so cannot enter passkey from it.
Is there an example...
Hello,
I am working on NUS service S110 8.0 softdevice and SDK 9.0 and added DFU feature for the application.
First, I connected to the device using MCP from PC. It...
Hi all,
I'm trying to use the nRF51822 sniffer to troubleshoot my TI CC2650STK sensortag ble communication and the output is slightly confusing. The problem I am having...
