Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I must create an application for nrf5 dk with s132 v3.0.0 sd. In this application a device must implement heart rate service client, while continously trasmitting a reference...
Dear Nordic Engineer,
I need to work on nRF52, my Macbook Air has OSX Yosemite 10.10.5 - I can run "make" or "nrfjprog" only if I copied libjlinkarm.dylib into the same...
Hi
I am presently working on MPU92/65 sensor interfacing with TWI/I2C.
i am using nRF51822 EK with soft device s130_nRF51_2.0.0(id:0x0080) and nRF5 SDK v12.2.0 and keil...
using
nrfjprog --rbp all
and got a success
and using
nrfjprog --readuicr
got unavaible
but if using j-flash and read whole chip, it's able to be readback...
it...
I am trying to figure out how/if I can program the softdevice hex from keil? I know I can just use nRF studio however its annoying sometimes....I also noticed I cannot rebuild...
I'm using an nrf52dk (pca10040) to develop an mqtt subscriber application.
I'm using the IoT softdevice, with the IoT 0.9.0 sdk example for subscriber as a starting point...
Hi,
I want to know in general about the UUID that we add in to GATT files.
Basically, I want to know that there are different UUIDs for different applications heart...
Hello everyone,
I successfully implemented the static key to access a characteristic now I want the user to udpate the passkey through another characteristic (which is also...
Hello, with a little research, I now decided that this is the general but incomplete (which is why I'm asking the question) step :
Immediately look up SP register, if the...
Hello,
we developed a custom board using the nRF52832. We are having problems communicating with the mma8652fc accelerometer using I2C. We also have a Rigado BMD-200 EVAL...
Problem : After successful compilation of ble_proximity example in SDK 12 version
Ble is not showing up in Android device
How ever If I load pre compile file in example...
What is the difference between the GAP Device Name and the Complete Local Name in an advertising or scan response packet? Can the two be different?
We have a requirement...
Is it possible to support both LE Secure Connections Just Works pairing and Legacy Just Works pairing in a single device?
My concern at the moment is that if I require...
I have one problem with unsing uint64_t in application...
Im for test try simple demo:
uint64_t test = 1327644190303473294;
NRF_LOG_INFO("test: %"PRIX64"\n", test);...
