Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hello,
I want to use NORDIC nrf52 to perform some power consumption Analysis. Is there any eveloution board from NORDIC that don,t have debugger connected to it? I want...
Hi all,
Is there a tutorial that explain better the bonding information and whitelist? I have more doubt about that.
My first code i have pairing and bonding:
...
hello..
I'm actually working on nrf51822,i could complete the advertising part successfully("hello world")..NOW i want to add privacy feature which allows an advertiser to...
Hi there,
I am working on the SDK13 project template that I am modifying in order to install a vendor type uuid.
But my code crash on "advertising_init" and ble_advertising_init...
While using the secure bootloader image and test application works consistently using the development kit I have not been able to port the solution reliably for our custom...
hai
i am using mbed to program my nrf51822.i want to set the analog pin p6 as analog in in one situation and as a digital out in another situation. but i am unable to do...
Hello.
After executing the code below, the RAM was dropped and the program could not be written.
for(idx = 0; idx < 7; idx++)
{
NRF_POWER->RAM[idx].POWER = (POWER_RAM_POWER_S0POWER_Off...
I'm studing the project of ble_app_gls/PCA10040/SDK11.0/ ,I have got some questions about the RACP indication pending and retransmittion mechnism. In this project(File ble_gls...
enter code here Hi guys I have managed to program an example BLE_Serial program into the nrf51822 but I cannot see anything coming out from the TX and RX ? Please guide me...
I've tried to install nRF Connect v2.0 on both Win 7 and Win 10 systems, both running Avast Anti-virus (up to date). In both cases the antivirus gives a warning about IDP...
I have the Memory Manager module enabled in my custom sdk_config. Within the module, I have both of the following defined.
MEM_MANAGER_ENABLE_LOGS 0
ENABLE_DEBUG_LOG_SUPPORT...
Hello - Is the long range option programmable in BT 5.0? During the run time, is it possible to switch between high speed and long range mode dynamically depending on the...
I am specific about master as I have to connect two simultaneously(obviously to two different pins pair). Plz provide any code outline if you have, Thank you in Advance
Hi.
I would like upload firmware from Atmel microcontroller to nRF51822 with SD130.
I suppose that I have to use single_bank_serial_s130 in nRF51822AA, but what I have to...
Hi,
I'm trying to implement dfu bootloader over uart, not dfu bootloader over air.
Where can I find a reference source code of dfu bootloader over uart?
regards ...
