I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Building for a PCA10040 dev board (nrf52832) in SDK 14.0.0 with the S132SD v5.0.0
I'm an encountering an issue where calls to printf() are only displaying a single byte...
Most application examples which use the scheduler have a main loop looking something like this,
int main(void)
{
// Initialization <snipped>
// Enter main loop...
Hi,
"wait" hangs when running the mbed blinky example, build in develop or release, on nrf52840.
The program is flashed with a J-Link and the program runs OK at first...
Dear support,
I am working on some custom boards embedding the nRF52832-CIAA chip using SDK-v11.0 and s132-v2.0.1.
I have got 9 custom units and out of them only 1 cannot...
We have ordered nRF52840 development kit . In windows xp comp port is coming as 8 but the device status in general is this evice cannot start.(code 10). Same in windows 7...
Hi,
I am working on ble_app_uart_c central code provided in sdk12.3.0 with softdevice s130.I added pwm code provided in peripheral examples in ble_app_uart_c central code...
Hi all,
I wanted to know the default values for the different NRF Radio paramateres in the ble_uart example.
I want to make some tests but not sure what is set as default...
Hello sir,
we have completely develop product using nRF52832 and S132, sdk13.1, and its great working fine with BLE. But for same application we want to use wifi module...
For my audio application, I need to convert pcm out from pdm module(nrf52832) to an audio format (mp3,wav) continuously. Is there any method or procedure for this??...or any...
This may be intentional, or an oversight but the
uint32_t app_gpiote_user_register(app_gpiote_user_id_t
* p_user_id, uint32_t const * p_pins_low_to_high_mask, uint32_t...
Dear All,
I am starter for nRF52832 DK. Could you please tell me where the start point is and where I can find demo programs ?
Thank you so much.
Best regards,
...
I want connect with password with my nrf52832 via Android phone. How I can do it? I do not want to do pairing how in example project "ble_app_gls". I used Android 6, SDK14...
we have used the ble mesh sdk v0.9.2 to implement long range ble mesh network on nrf52840 SOC
it is successfully working with s132 softdevice. with default configuration...