Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
Hello Team,
I have flashed the bap_unicast_server bluetooth sample on my nRF5340 Audio DK. No build or flash errors. When I connect to my phone it connects properly. I'm...
Hello team,
I am using nrf54l15 dk for the devlopment and want to read the RTC counter to check for how much time my device was in sleep mode.
How to achive this?
Thanks...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I'm having trouble porting my project from the older SDK (2.6.0) to the new SDK.
I thought the most straightforward way to do that would be to start with a sample project...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
Hi Nordic Support Team,
I'm currently experimenting with Channel Sounding using a couple of nRF54L15 boards.
I am trying to obtain raw I and Q samples so that I may analyze...
Hi,
I need to enable an input interrupt on nRF52832 and I want to use a GPIOTE EVENTS_IN channel.
During boot configuration, I'm using nrfx_gpiote_in_init function with...
There are two NUS services here, but only the second one can send data through the RX characteristic. I've checked the source code and nothing has changed. How do I delete...
Hello Nordic support team,
Forgive me if I am asking a stupid question.
In the source file ble_conn_params.c, there is a function called ble_conn_params_init() and I...
I am working on a wearable GPS tracking device using the nRF9151 DK and testing the GNSS example code. However, I am facing an issue with the cold start time for acquiring...
I recently bought a fanstel blg840 device, and I have programmed At client firmware in nrf91 and custom code into nrf52, but the problem is nrf52 is sending at comments to...
Hello,
I'm sure you know this already, but there seems to be a problem with the subject footprint. I guess I'm posting this to confirm that it in fact does have a bug in...
Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hi, I want to achieve high speed data transfer between NRF7002 DK with other development board. Therefore, I want to using SPI4 with 32MHz speed. However, I found out that...
